Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
• To prevent a possible fire, do not block air intakes or exhausts in any manner. • Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire or could damage the heater. • This heater has hot electrical parts inside. DO NOT use it in areas where gasoline, paint or flammable liquids are used or stored. • Use the heater only as described in this booklet. Any other use is not recommended by the manufacturer which may cause fire, electric shock or injury to persons. • Fully remove the power cord from the cord storage before use. Always uncoil the power cord before applying power. • This product must always be used AND STORED in the upright position. Warning: in order to avoid overheating, do not cover the heater. COMPULSORY WARNING If the supply cord is damaged, the cord must be replaced by the manufacturer. This Column Heater is filled with a precise quantity of oil. Repairs requiring the opening of the oil container are only to be conducted by the manufacturer or a qualified authorized service agent who should be contacted if there is an oil leakage. Disposal of the oil should be in accordance with local regulations. You should contact your local council to determine the correct procedure. This product has not been designed for any uses other than those specified in this booklet. SAVE THESE INSTRUCTIONS YOUR HEATER COLUMN Before first using your new appliance, it is most important that you read and follow the instruction in this use and care booklet, even if you feel you are quite familiar with this type of appliance. Your attention is drawn particularly to the section dealing with “IMPORTANT SAFEGUARDS”. Find a place and keep this booklet handy for future reference. Your Column Heater is easy and safe to use. It has been designed to function quietly and safely under normal circumstances. Read all instructions to ensure safe and efficient use. HEATING The columns or fins are filled with a special oil that conducts heat to the metal surfaces. These in turn warm the air around them which gently and silently heats the room. Be careful because they work under pressure as the oil inside heats up. Like any electrical appliance, this product may cause injury or damage property if used whilst damaged. MOUNTING THE FEET 1. Place the column heater upside-down on a scratch-free location, make sure it is stable and will not fall. 2. First snap the cord holder onto the front foot. (Note: the oval concave should be upwards.) 3. Snap the front foot onto the front cover and then use two short screws provided to fix the front foot in place. 4. Snap the back foot onto the back cover and then use two long screws provided to fix the back foot into place. NOTE: After wheels assembled as to above, take the unit in upright position, if you find unit is not stable on the ground, you can adjust the two screws on back wheels. WARNING: Do not operate without feet attached. Operate the heater only in an upright position (feet on the bottom, controls on the top), any other position could create a hazardous situation. NOTE: After attaching the feet wait at least 15 minutes for the oil in each fin to setting before using the column heater. OPERATION 1. Before using the heater make sure that it is on a flat and stable surface. Damage may occur if it is placed on an incline or decline. 2. Set all the controls to OFF position, and insert the plug into a socket-outlet that is well grounded. Be sure plug fits tightly into outlet. Be sure that the main power switch is on before operating the control panel. 3. Operation for control panel. 1.) SETTING THE CLOCK Set the clock to the correct time before using the heater, proceeding as follows: Press the button “hour” until the display shows the hours for the correct time, then release the button. Press the button “minute” until the display shows the minutes for the correct time, then release the button. Whenever you want ot modify hours or minutes during operation, just proceed as above. NOTE: Do not modify the clock while the heater is operating in auto mode. To activate the set time, you must release the button “hour” or “minute” for at least 5 seconds. 2.) SETTING THE POWER The variable power setting determines how fast the desired temperature is reached. The higher the power setting, the more energy is used. NOTE:If you want to operate the appliance in manual mode, press the button “power setting” to activate it. In this mode, the function of the booking timer will be invalidated. To set the required power level, proceed as follows: press the “power setting” button one or more times within 5 seconds to select the power level, as per the following sequence: The power selecting can be circulated and the red power pilot light will be on during the heater powered on. To cancel the manual mode, push the button “power setting” until the LCD appear “OFF”, the red power pilot light will be extinguished. Now the unit can be set in auto mo...