Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Figure 3 low high auto mode HIGH (1500 Watts) AUTO LOW (1000 Watts) MODE Note: The "auto" light only illuminates when the unit is set to "auto" mode by the remote. B. Remote is ON and Unit is ON: 1. Press the Mode button on the unit. The unit will then switch "Modes"; either from "Low" to "High", "High" to "Off" or "Auto" to "Off" . The unit’s lights will reflect the change. The Remote will display a different mode – the mode in which it was left. If a button is pressed on the Remote, the Remote’s signal will override the "Mode" on the unit and the two will be back TIMER FUNCTION: Using Timer to turn unit off 1) Hold mode button for 2 2) Push + and - together. 2.1) "timer" turns on. 1 Hr appears screen. 3) Push + or run before it automatically 3. Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 Watts, this unit draws 12.5 Amps. Note: The power light will remain lit during operation ASSEMBLY INSTRUCTIONS Wheel Assembly Tools required for assembly: Phillips head screwdriver Carefully unpack your Bionaire ® heater from the box (it is recommended to save the box for off-season storage). You will find the following pieces: 1. Four casters (wheels) 2. Four screws 3. Two caster (wheel platforms) WARNING DO NOT ATTEMPT TO OPERATE THE HEATER WITHOUT THE WHEELS IN PLACE CasterPlatform(Wheels) Fig. 1 Casters 1. Make sure the unit is X 4 unplugged. Using a slotted or Phillips head screwdriver, attach two casters to each caster platform. 2. Carefully turn the unit over so the caster platforms can be attached. 3. Slide the caster platform into the bottom of the plastic end cap, following the grooves (shown in Fig. 1). 4. Repeat this sequence on the other side of the heater, making sure both sides are secure. 5. Return the console to its upright position. FIRST USE ONLY: 1. Put batteries into Remote. The "Room" temperature is displayed at all times. (Use 3 AAA batteries do not mix alkaline and heavy duty batteries) 2. Plug unit into outlet. The first time the unit is plugged in, it will beep every two seconds the remote. To sync unit with remote follow the below steps: Unlock remote. (This must be done each use of the remote) To Unlock remote, hold down the button for 2 seconds from the screen. Once the is unlocked, the mode button times telling DO SYNC more than 1 unit at once. A hazardous situation may occur. Note: If the batteries are running low on power, a low battery indicator will appear on the remote. Low batteries will affect transmission distance and the screen contrast. We recommend replacing batteries immediately. Figure 2 mode Note: The maximum transmission distance for this remote is 30 ft., Do not use remote more than 30 ft. from appliance. Remote must be used in same room as appliance. Note: Galileo™ can be used in either Fahrenheit or Celsius. To change the reading on the remote, flip the remote over and push the button located on the right hand side under the stand with a ball point pen tip. This switch will change the reading from °F to °C and vice versa. Note: Every minute while in Auto mode, the Galileo™ communications with the base unit. If the Galileo™ goes out of range and/or has low batteries, the communication will stop, and after 8 minutes of non-communication unit will shut off. MANUAL OPERATION WITH REMOTE 1. Press Mode button on the remote. "Low" illuminates on remote screen indicating mode. The power light on the unit will turn on. The unit turns on and operates in "Low" mode. The illuminate. In this mode, the its low wattage. 2. Press Mode button on a second time. remote screen will now display "High" The unit’s "High" light will run in this mode. In this mode continuously Note: While using the remote, the backlight function will turn on when any button is pushed and will turn off after 10 seconds of non-use. Note: Do not cover remote while in use, this may affect the accuracy of the temperature reading. Note: Do not place remote under lamps as the radiant heat from the lamp may affect the accuracy of the thermostat. Note: Because heat rises, and the GalileoTM remote senses temperature, Bionaire recommends that you do not locate the GalileoTM remote higher than 4ft from the ground. By locating the GalileoTM more than 4 ft from the ground, you will get a less accurate temperature reading than under normal circumstances. Note: Do not place remote on control panel while in use. THERMOSTAT OPERATION WITH REMOTE 1. Press Mode button on remote until the remote screen displays "Auto" and "low". The "Set" temperature is displayed next to the "Room" temp. The unit will cycle on and off to maintain the "Set" temperature. The default room temp = 72.F. In this mode the unit will run to maintain the "Set" temperature. 2. Press Mode button on remote again. The remote screen displays "Auto" and "high". The "Set" temperature is displayed next to the "Room" temp. The "Auto" light on unit stays illuminated. The unit will cycle on and off to maintain the "S...