Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The heater will run continuously on LO. 3. Press the Mode Button for a third time for Auto Mode HI Power (AH) or press again for Auto Mode LO Power (AL). In either of these modes you may then press the up, and down buttons to reach your desired temperature. 4. Once you have reached your desired temperature, the display will return to current room temperature and gradually increase until the room has reached the preset temperature. 5. If the unit will not start in the digital thermostat mode, please make sure the “set temperature” is higher than the current room temperature. NOTE: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting. When the preset temperature is reached, the fan will run for 30 seconds without heat. This cool down process ensures an accurate and consistent temperature reading. If you unplug the heater, you will have to reset the digital thermostat again by following the above instructions. NOTE: To shut the unit off at any time, press and hold the MODE button down for two seconds. After heater is turned off, fan will run for 30 seconds to cool unit. NOTE: Digital thermostat has memory. The digital thermostat will remember the previous temperature setting after the unit has been turned off. However, if the unit is unplugged, the digital thermostat will be reset and will no longer remember the previous temperature setting. USING THE PROGRAMMABLE TIMER Digital thermostat allows the user to program the heater to turn on at a preset time, or turn off after a set amount of time. Setting the Off Timer: 1. Select the Mode and/or temperature you wish the heater to run in. 2. While the heater is running, press and hold the up and down buttons simultaneously. 3. By pressing the up and down buttons, program the heater to turn off in up to 16 hours from the current time, in increments of 1 hour. 4. After setting the timer, the LED display will return to show the current room temperature. A LED will illuminate to show that the timer is activated. 5. After the predetermined length of time has passed, the heater will automatically shut off. Setting the On Timer: 1. While the heater is off, press and hold the up and down buttons simultaneously. 2. By pressing the up and down buttons, program the heater to turn on up to 16 hours in advance of current time, in increments of 1 hour. 3. After the preset length of time has passed, the heater will automatically turn on at the last mode setting that was programmed. If no program was set, the heater will turn on Auto Mode HI Power at 75°F for a preset time of 2 hours. OSCILLATION INSTRUCTIONS 1. Select the desired temperature and mode settings and press the oscillation button to the ON position. 2. To stop oscillation, press the oscillation button again. 3. Please do not manually turn the heater on the base; it is designed to turn only by motorized oscillation. REMOTE CONTROL INSTRUCTIONS 1. Before operation, insert 2 “AAA” batteries into the back of the remote control. • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. The remote control for this unit has the capability of operating all control panel functions. Please note this remote control will not work through walls. POWER: To turn the unit on or off press the Power Button. MODES: To scroll through the various modes LO, HI, AL and AH press the Mode Button until you reach your desired setting. OSCILLATION: To start oscillation, press the Osc. Button once. To stop oscillation press the button again. TEMPERATURE: To increase the temperature setting, press the Temp Up button. To decrease the temperature setting that you desire press the Temp Down button. TIMER: To activate the timer from the remote control, press the Temp Up and Temp Down buttons at the same time. This will give you the ability to program the heater to turn on or off in 1 hour increments up to 16 hours. For more information see the Programmable Timer instructions above. CLEANING/MAINTENANCE During Season Care: 1. Always unplug the heater before cleaning 2. Clean the unit with a soft cloth moistened with a mild soap solution. 3. NEVER use abrasive or flammable solvents to clean the unit. 4. After cleaning, be sure to completely dry the unit with a cloth or towel. After Season Care: 1. Store heater in a cool, dry location 2. The manufacturer recommends that you store the unit in its original carton. . TIP: Over time, dust may accumulate on the front grills. This can be removed by wiping the unit with a damp cloth. Always unplug unit and allow to cool prior to cleaning TROUBLESHOOTING If your heater fails to operate: • UNPLUG THE UNIT • Make sure the electrical outlet or circuit breaker is working. •Check for obstructions. If you find an obstruction turn the heater OFF, and unplug the unit. Carefully remove the obstruction and follow the reset instructions. • The tem...