Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Dimplex Dateigröße: 189.93 kb Dateiname: 2b3aebad-9bb7-4968-8241-c8772c0bc783.pdf Unterrichtssprache:

The supply circuit to each heater must incorporate a double pole isolating switch having a contact separation of at least 3mm Model A B (Minimum) Pilot Wire Connection APL100 468 225 The BLACK control wire is designed to carry a signal from slot in or wall mounted Dimplex APL150 618 285 programmers. If, however a programmer is not being used, the pilot wire should be isolated in accordance with the current IEE Wiring Regulations. Do NOT connect the BLACK pilot wire to earth Any 240V insulated cable may be used to link pilot wires around the ring main. A low signal current is used. Suitable connections would be either an additional single core wire marked or colour coded appropriately or use a 4 core cable throughout the ring main. Please refer to the relevant programmer installation and operating instructions for further details on pilot wire connection Operation Mode Selection Dial (A) Use this rotary dial to select the function you require Symbol Function Description Heater will switch on to provide frost Frost Protection protection if the room drops below 5.C Advice on Using your Heater • For greatest economy switch the heater to economy (setback) if you leave the room for long periods of time or before going to bed. • Do not set the comfort level too high. Even small reductions on the thermostat setting can save a lot of energy. • If you go away for a long period of time select the frost protection setting on the function dial or reduce the thermostat setting to a lower level. Locking the Thermostat Setting (C) If necessary you can lock the thermostat dial to a single setting or range. To lock the settings, use a small pair of narrow nosed pliers to pull out the locking pins at the rear of the thermostat dial. The following settings can be obtained: (see Fig.4) • Single setting – Set thermostat dial to desired setting (eg no.6). Locate one pin directly opposite the setting required • Minimum setting – Set thermostat dial to desired setting (e.g. no.6). Locate one pin opposite the setting required and one hole to the left. (The thermostat will now be adjustable from 6-9 only) • Maximum setting – Set thermostat dial to desired setting (eg no.6).Locate one pin opposite the setting required and one hole to the right. (The thermostat dial will now be adjustable from 1-6 only) • Minimum - maximum setting – (e.g. no.2-4) Locate both pins and space apart until desired range is found Heater will maintain a lower Economy (set back) temperature level for background heating (comfort less 3.5.C) Heater will maintain the temperature Comfort set on the thermostat dial Off Off Heater will not function Heater will be controlled by a Programme programming device Fig.4 Note: If the programme function is selected but no programming device is being used, the heater will function in comfort mode The following Dimplex programmers are available: Pilot Wire Wall Mounted Controller (2 Zone) – Part no. RX010006 MBS Wall Mounted Programmer (2 Zone) – Part no. RX010007 MBS Slot in Receiving Cassette – Part No. RX9913 MBS Slot in Programming Cassette (Single Zone) – Part no. RX9912 Pilot Wire Programming Cassette (Single Zone) – Part no. RX9911 Function Display (B) Neon indicators adjacent to the function selector will light to show the mode selected Setting the Comfort Temperature (C) Use the thermostat dial (C) to select your desired room temperature. The markings on the dial are in approximately 3.5.C increments. The settings are numbered 1-10 (MAX). The quickest way to find your comfort setting is to turn the thermostat dial to the maximum setting. When your ideal comfort level is achieved, turn the thermostat dial down until the thermostat switches off (the neon light will go out) Leave at this setting and the heater will automatically maintain the desired temperature. Thermostat Light (D) The neon indicator below the thermostat will light when the heater is operating. Background (set back) The economy setting is preset at – 3.5.C this is the amount the room temperature will be allowed to drop when you switch the function selector from comfort to economy. Reverting to comfort mode will automatically cause the temperature to rise to the setting on the main thermostat. To Lock the Control Cover (F) A screw is provided to permanently lock the cover in position. It is located on the back of the control box, under the thermostat dial. Remove this and screw through the notch below the lifting tab into the plastic housing. (see also Fig.4 above) Safety A thermal cut-out will switch off the heater if, for any reason, it overheats. Should the cut-out operate, switch off the mains supply and allow the heater to cool. Once the heater has cooled sufficiently remove the obstruction and switch on the mains supply. Cleaning Before cleaning your heater, switch off the heater and allow it to cool. Disconnect the electricity supply to the appliance. The outside can be cleaned by wiping it over with a soft damp cloth and then dried. Do not use ab...

Herunterladen

Geben Sie zwei Ziffern: