Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
2. Drain Fuel Tank through Fuel Cap Opening and wash Fuel Cap Filter with clean fuel. 3.Using a small amount of kerosene,swirl and rinse the inside of the tank. Never mix water with the kerosene as it will cause poor operation of the heater. Pour the kerosene out making sure that you remove it all. IMPORTANT : Do not store kerosene over summer months for use during next next heating season. Using old fuel could damage heater. 4. Reinstall Fuel Cap Filter and Fuel Cap(See Figure 11). IMPORTANT : Reinstall Fuel Cap Filter fully into Fuel Cap Opening on tank, Otherwise it will not install completely. Figure 10. Remove Fuel Cap and Filter Figure 11. Reinstall Fuel Cap Filter 5.Store heater in dry well ventilated area. Make sure storage place is free of dust and corrosive fumes. 6.Store the heater in the original box with the original packing material and keep the USER'S MANUAL with the heater. 9 9. MAINTENANCE WARNING!! : NEVER SERVICE HEATER WHILE IT IS PLUGGED IN OR WHILE HOT! USE ORIGINAL EQUIPMENT REPLACEMENT PARTS. Use of third party or other alternate components will void warranty and may cause unsafe operating conditions. A.) FUEL TANK FLUSH EVERY 200 HOURS OF OPERATION OR AS NEEDED (SEE STORAGE, PAGE 9) B.) UPPER SHELL REMOVAL -Remove Screw that secure Side Cover. -Push out for arrow direction and extract Side Cover's Bracket from Rectancle Hole and Separate Side Cover(R). -Side Cover(L) in opposite of Side Cover(R) Separates by same method. (RMC-KFA120T/170TDLX Models Only.) -Remove 4 Screws along each side of heater using medium phillips screwdriver. These Screws attach Upper Rear and Lower shells together. (See Figure 12) (RMC-KFA65TDLX Model Only.) -Remove Screws along each side of heater using medium phillips screwdriver. These Screws attach Upper and Lower shells together. C.) AIR OUTPUT,AIR INTAKE AND LINT FILTERS WASH AND DRY WITH SOAP AND WATER OR REPLACE EVERY 500 HOURS OF OPERATION OR ONCE A YEAR. -Remove Upper Shell.(See Figure 12) -Remove Fan guard.(See Figure 13) -Remove End Filter Cover Screws using medium phillips screwdriver. -Remove End Filter Cover. -Replace Air Output and Lint Filters. -Wash or Replace Air Intake Filter. -Reinstall Fan Guard and Upper Shell. 10 Figure 12. Upper Shell Removal. Figure 13. Air Output,Intake,and Lint Filters NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! D.) FAN BLADES CLEAN EVERY SEASON OR AS NEEDED. -Remove upper shell(See 10 page.) -Use 1/8" allen wrench to loosen set screw which holds Fan Blade to motor shaft. -Slip Fan Blade off motor shaft. -Clean Fan Blade using a soft colth moistened with kerosene or solvent. -Dry Fan Blade throughly. -Reinstall Fan Blade on motor shaft. Place Fan Blade hub flush with end of motor shaft. -Place Set Screw on flat of shaft. Tighten Set Screw firmly(40~50 inch-pounds/4.5~5.6 N-m). E.) NOZZLE REMOVE DIRT IN NOZZLE AS NEEDED(See Page 14) -Remove Upper Shell(See page 10). -Remove Fan Blade(See Fan Blades). -Remove Fuel and Air Line from Burner Head. -Remove Ignitor Wire from Spark Plug. -Remove three Screws using medium phillips screwdriver and remove Burner Head from combustion chamber. -Remove Spark Plug from Burner Head using medium phillips screwdriver. -Carefully remove Nozzle from Burner Head using 5/8" socket wrench. -Blow compressed air through face of Nozzle.(this will remove any dirt in Nozzle) -Reinstall Nozzle into Burner Head and tighten firmly. (80~110 inch-pounds) -Reinstall Spark Plug in Burner Head. -Attach Ignitor wire to Spark Plug. -Attach Fuel and Air Line to Burner Head. -Reinstall Fan Blade and Upper Shell. 11 Figure 14. Fan and Setscrew Location. Figure 15. Removing Nozzle F.) SPARK PLUG CLEAN AND REGAP EVERY 600 HOURS OF OPERATION OR REPLACE AS NEEDED. -Remove upper shell(See 10 page). -Remove Fan Blade(See 11 Page). -Remove Ignitor Wire from Spark Plug. -Remove Spark Plug from Burner Head using medium phillips screwdriver. -Clean and regap Spark plug electrodes to 0.140.(3.5mm) gap. -Reinstall Spark Plug in Burner Head. -Attach Ignitor wire to Spark Plug. -Reinstall Fan and Upper Shell. G.) PHOTOCELL CLEAN PHOTOCELL ANNUALLY OR AS NEEDED. -Remove upper shell(See page 10). -Remove fan (See page 11). -Remove photocell from photocell bracket. -Clean photocell lens with cotton swab. TO REPLACE: -Disconnect switch wires from power switch. -Remove two Screws using medium phillips screwdriver. These Screws attach Main PCB to Side Cover.(See Figure 17) -Remove Side cover(R). -Disconnect Photocell Connector from Circuit Board and remove photocell. -Install new Photocell and connect photocell connector to Circuit Board. -Replace Circuit Board to Side Cover(R) and Switch wires to Power Switch. -Replace Fan and Upper Shell. Figure 16. Removing Spark Plug Figure 17. Replace & Cleaning Photocell 12 NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE TH...
Dieses Handbuch ist für folgende Modelle:elektrische Heizungen - RMC-KFA120TDLX, RMC-KFA170TDLX (471.91 kb)