Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Black & Decker Dateigröße: 3.23 mb Dateiname: Unterrichtssprache:

To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized service personnel. SPECIAL ATTENTION: The use of an extension cord is not recommended. However, if it is absolutely necessary, be sure that the cord is (1) No. 14 AWG minimum size and rated no less than 1875 watts; (2) UL Listed; (3) as short as possible (long cords can overheat, as well as trip circuit breakers); (4) not used for operating more than one appliance at a time. Note: If the power supply cord is damaged, it must be replaced manufacturer or its service agent or a similarly qualified avoid a hazard. 2 How to Use This appliance is intended for household use only. Important: For warranty verification, do not remove line cord sticker. The Advanced Safety Technology™ (AST) system features unique technology built into your heater that offers protection detailed in the "Special Features" section. Before Use: Important: During the first few minutes of initial use, you may notice a slight odor. This is normal and will quickly disappear. This heater is intended for use on a flat, stable surface, such as a floor, tabletop, shelf, or desk in a location where the airflow grille openings won’t be obstructed. Do not use in wet or moist locations, like bathrooms or laundry areas, or in areas where paint or other flammable or volatile liquids are used or stored. Caution: Be sure no other appliances are plugged into same circuit with heater/fan. A circuit overload could occur. 1. Place heater on a flat, stable surface, such as a floor or tabletop where airflow grille opening won’t be obstructed. Use fold-down handle when moving unit. Do not use in wet/moist locations, like bathrooms or laundry areas, or in areas where paint, flammable, or other volatile liquids are used or stored. 2. Be sure control knob is in the OFF position, then plug heater into a standard AC outlet. 3. Room Select: Turn switch to the appropriate setting for a small (approx. 10' x 10'/3 m x 3 m), medium (approx. 12'x12'/3.8 m x 3.8 m) or large (approx. 12'x 16'/3.8m x 5m) room (B) 4. Turn thermostat control to HOT to activate heater. Once desired room temperature is achieved, lower thermostat control toward FROST WATCH until unit cycles off. The thermostat will cycle unit on and off to maintain your comfortable temperature level. 5. Turn timer knob to the 1 hr., 2 hr., 3 hr. or 4 hr. setting to select how long you’d like heater to stay on. The unit will shut off automatically once the selected time runs out. To operate heater continuously, turn timer knob to ON. Remember to shut unit Off when done. 6. To use as a fan without heat, move control knob to FAN ONLY and thermostat control toward HOT until fan begins to operate. No heating will occur in this mode. 7. To turn off, turn thermostat control to FROST WATCH and control knob to Off. Note: The power indicator light shows heater is on and operating. It continues to glow even if thermostat has cycled off and heating elements are off. 8. Frost Watch: When heater is plugged in and POWER indicator light is on, you can select any setting for room size (depending on your model) and leave thermostat control on toward lower settings or FROST WATCH. Heater will remain off unless the temperature drops below (40° F/4°C). If this happens, FROST WATCH will automatically cycle unit on to protect against freezing pipes or frost damage. 3 4 Product may vary slightly from what is illustrated. 1. Fold-down handle 2. Timer knob 3. Control knob 4. CAUTION indicator 5. Heat sensor patch 6. Front grille 7. Roll-over bars 8. Power indicator 9. Thermostat control B 200UHPub1000002035 4/15/05 1:53 PM Page 4 200UHPub1000002035 4/15/05 1:53 PM Page 6 Special features and the Advanced Safety Technology™ (AST) system 1. This unit has a safety auto off, plus a safety thermal fuse and CAUTION light. If unit experiences excessive heat, the safety auto off will shut off unit, and the CAUTION light will go on. If this happens, turn control knob to OFF immediately. Be sure front grille is not blocked and nothing is restricting airflow. Unplug unit, let it cool down, and wait 10-15 minutes. To reset, plug unit back in and turn thermostat control to HOT. You can then readjust temperature or room settings. If unit fails to operate after 15 minutes, it may mean heater has internal damage and thermal fuse has been tripped so heater can no longer operate. 2. A built-in tip-over switch will cut power if the unit is accidentally knocked over forward or backward. To reset, simply place heater in upright position on a level surface. If it falls forward, the roll-over bars on the front of unit will help prevent heater from burning surfaces. C 3. Even though unit has a cool-touch housing, the front grille will get hot. Be careful not to touch it during operation. This patch changes color when front grille becomes hot to the-touch (C). Do not touch front of hea...

Herunterladen

Geben Sie zwei Ziffern: