Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
e. Thermocouple defective - replace. f. Gas control defective - replace. 4. Main burner does not ignite. a. Main burner orifice is blocked - clean, see "Appliance Maintenance," above. Inlet gas pressure too low, contact gas supplier. 5. Heater keeps shutting "OFF" during normal operation. a. Pilot is blocked - clean pilot, see Page 11. b. Inlet gas pressure too low, contact gas supplier Page 12 R-2688 PARTS LIST PARTS LIST PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide. Index Part No. Number Description 1 R-1981 Piezo Ignitor 2 VF-167 Casing Assembly 3 SR-113 Valve Bracket 4 R-2710 Gas Valve - NAT Gas 4 R-2711 Gas Valve - LP Gas 5 R-2423 Male Connector 6 VF-166 Outlet Tubing 7 VF-165 Inlet Tubing 8 R-2423 Male Connector 9 VF-140 Top Shield 10 VF-131 Chamber Back 11 P-213 Orifice - NAT Gas 11 P-204 Orifice - LP Gas 12 P-212 Orifice Fitting 13 VF-138 Front Shield Assembly 14 SR-209 Regulator Bracket 15 R-2784 Inlet Regulator - NAT Gas 15 R-2480 Inlet Regulator - LP Gas 16 VF-147 Heat Shield 17 VF-148 Pilot Shield 18 VF-126 Front Hood 19 VF-123 Casing Front 20 VF-141 Screen Assembly 21 VF-125 Front Trim Index Part No. Number Description 22 23 24 25 26 26 26 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 VF-150 Frame Assembly R-1945 Ignitor Wire 732063 Electrode R-1970 Thermocouple 762143 Natural Pilot with Bracket 762255 LP Pilot with Bracket R-1968 Pilot Assembly - NAT Gas (Includes Items 24, 25 & 26) R-1969 Pilot Assembly - LP Gas (Includes Items 24, 25 & 26) R-2715 Main Burner VF-151 Air Shutter - Used with LP Gas VF-055 Pilot Tubing R-2680 Ceramic Log VF-152 EEB-1 Blower Kit 8720161 Bushing VF-153 Mounting Bracket R-2695 Motor R-2696 Fan Blade R-2104 Fan Control DV-806 Switch Box DV-807 Switch Box Cover R-2113 Spacer 872087 Bushing R-2091 Wire Assembly R-2099 Cord Set USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH. HOW TO ORDER REPAIR PARTS Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the service person/dealer. All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate illustration and list. Be sure to give all this information . . . Furnace Model Number Part Description Furnace Serial Number Part Number Type of Gas (Propane or Natural) Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store. Shipments contingent upon strikes, fires and all causes beyond our control. R-2688 Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois 62222-0529 Page 13 Page 14 R-2688 PARTS VIEW R-2688 Page 15 INSTALLING OPTIONAL BLOWER EEB-1. If heater is installed on wall, in order to install optional blower, the heater must be removed from wall. 1. Remove casing front assembly. 2. Align (2) clearance holes on motor mounting bracket with (2) screw holes on casing assembly back and attach motor mounting bracket with (2) #10 x 5/16" (8mm) screws provided. The motor wires should be facing to the left and then routed behind the motor mounting bracket and to the right as depicted in Figure 1. 3. Route cord set through 9/16" (14mm) hole on casing assembly back. Insert approximately 3" (76mm) of cord set into casing assembly back. 4. Attach the green ground wire from the cord set beneath one of the #10 x 5/16" (8mm) screws on the motor mounting bracket (see Step 2). Remove #10 x 5/16" (8mm) screw, align ring terminal of green ground wire with clearance hole on motor mounting bracket and replace #10 x 5/16" (8mm) screw into motor mounting bracket. 5. Remove (2) #10 x 1/2" (13mm) screws from the right side of the front shield assembly. 6. Remove (1) #10 x 1/2" (13mm) screw from the top shield. 7. Grasp front shield above screen assembly and pivot right side of front shield forward approximately one inch. Figure 1 8. Remove #8 x 3/8" (10mm) screw from switch box cover and remove switch box cover from switch box. With fan control wires facing upward, place 3/16" (5mm) spacer behind oblong clearance hole on switch box. Locate 1/8" (3mm) screw hole on right side of front shield assembly by measuring down 9" (229mm) from the upper right corner of the shield assembly (See Figure 1). Align 3/16" (5mm) spacer and oblong clearance hole on switch box with 1/8" (3mm) screw hole on right side of front shield assembly. Attach (1) #10 x 1/2" (13mm) screw provided, by inserting screw through oblong clearance hole and 3/16" (5mm) spacer and into the right side of the front shield assembly. 9. Attach switch box cover to switch box with the #8 x 3/8" (10mm) screw removed in Step 8. 10. Replace (1) #10 x 1/2" (13mm...