Stimmen - 5, Durchschnittliche Bewertung: 4.2
(
)
)
|
Anleitung Zusammenfassung
Attach vent cap to outside mounting plate with three (3) 10 x 1/2” screws. 4. Reassembly and resealing vent-air intake system is completed. Installing a Vent Near a Window Ledge, Other Type of Projection or on Siding (vinyl, aluminum, etc.) Direct vent furnaces are designed to be installed on a uniform outside wall. When the wind comes from any angle (up, down or from either side), it must hit the vent cap equally over both the air inlet and the flue outlet portions of the vent. Any wall projection, such as a door or window casing, which disturbs the wind on one side of the air inlet section will result in back pressure on the flue section smothering the flame and eventual pilot outage. When the vent cap is to be installed on siding or it appears that a projection within 6” of any side of the air inlet section could shield the air inlet section, the entire vent should be supported away from the wall at least the distance of the projection. 2” x 4” framing whose outside dimensions match the overall dimensions of the mounting plate is recommended. The 2” x 4” framing protects siding from possible warpage or discoloration. All joints can then be sealed and painted. The wall depth plus the additional depth of the 2” x 4” framing should not exceed a total depth of 14” for DVC-35T. (See Figure 10) Vinyl siding vent kit, DV-822, is available from Empire Comfort Systems, Inc. The depth is 3”, which enables the vent cap to be extended away from siding or projections. The wall depth plus the additional 3” depth of the vinyl siding vent cap extension should not exceed a total depth of 19” for DVC-35T. (See Figure 11) Warning: When vinyl siding vent kit, DV-822 or 2” x 4” framing is added to an existing installation (furnace is installed) do not attempt to add sections of pipe to the flue outlet tube or air inlet tube. An air tight seal is required for both tubes. Refer to Parts List, page 16 to order tubes. Figure 10 Figure 11 13119-6-0107 Page 11 FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. TO TURN OFF GAS TO APPLIANCE 1. Set the thermostat to lowest setting. 2. Turn off all electric power to appliance if service is to be performed . 3. Remove control access panel (lower front panel). 4. Push in gas control knob slightly and turn clockwise to “OFF.” Do not force. 5. Replace control access panel (lower front panel). LIGHTING INSTRUCTIONS 1. STOP! Read the safety information above. 2. Set the thermostat to lowest setting. 3. Turn off all electric power to the appliance. 4. Remove control access panel (lower front panel). 5. Turn gas control knob clockwise to “OFF.” 6. Wait ten (10) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you don’t smell gas, go to the next step. 7. Remove the pilot ac- cess cover located on the combustion cham- ber. 8. Find pilot -follow metal tube from gas control. The pilot is located between the two burner tubes behind the pilot access cover. 9. Turn gas control knob counterclockwise to “PILOT.” 10. Push and hold red reset button down completely and repeatedly push the ignitor button until the pilot burner is lit. Pilot may also be lit with a match. Continue to hold the red reset button down for about one (1) minute after the pilot is lit. Release button and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 5 through 10. • If button does not pop up when released, stop and immediately call a qualified service technician or gas supplier. • If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier. 11. Replace pilot access cover. 12. Turn gas control knob counterclockwise to “ON.” 13. Replace control acce...
Dieses Handbuch ist für folgende Modelle:elektrische Heizungen - DVC-35T-1 (1.33 mb)