Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Make sure that all 4 holes line up properly. • Insert (4) Small Screws enough to hold Engine in place. They will be fully tightened at the end of Step 7. Note: Do not replace Engine Access Panel until Step 13. Step 6 - Attach Engine/Post to Platform • Insert end of Post without holes over Gas Line, being careful not to bend Gas Line. • Slide Post into collar of Platform so Post rests completely on Platform. • Tighten bottom three setscrews with hex (Allen) wrench supplied. • Make sure Post is perpendicular to Base. • Use top three setscrews to adjust Post's angle as necessary. • Tighten all six setscrews. Note: Post must be perpendicular to Base. Failure to do so will adversely affect burner performance. •AV,", •A'mVVVi yv, w , •sim ,WAÎ ,;vyW Owner’s manual and assembly instructions: model 200209 outdoor patio heater 1/15/03 8 Endless Summer Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 7 - Connect Gas Line to Engine • Attach Gas Line to Control Valve: • Pull collar of Gas Line back. • Insert Gas Line over Control Valve. • Release collar and it should lock in place. (Tip - push Gas Line up from bottom of Post to make a good seating before releasing the collar.) • Gently tug on line to test for proper connection. If Gas Line moves it is not properly connected. Do not proceed until you have a proper connection. • Fully tighten the (4) screws from Step 5. Step 8 - Assemble dome Note: Each dome section has a pin mounted in place in the rolled bottom edge. If necessary for proper alignment of dome sections, loosen each screw prior to further assembly and retighten after sections are aligned. • With the large side facing up, slide a dome rib on to the same side of one dome section as the pin. Slide two dome sections together, allowing the exposed end of the pin slide into the rolled edge of the next dome section. Line up hole in dome with threaded hole in pin. • Insert one Dome Screw and secure loosely. • Repeat procedure to complete the assembly of all three sections. • Slide Dome bolt through bottom check plate (with small center hump), being sure that the rolled edge faces down. • Slide bolt from previous step through the center of the assembled dome sections, and be sure that the rolled edge of the check plate fits inside of the ends of the three Dome Ribs. Also be sure that the slots in the check plate line up with the holes on the dome sections. • Slide the other check plate over the Center bolt with the rolled edge facing up, again making sure that the plate fits inside of the Ribs and the holes line up with those in the dome. • Spin the medium nut all the way down the bolt, clamping all of the pieces in place, making sure that all of the humps fit inside one another. • Fully tighten all of the screws in the rolled edge. • Slide Dome Cap over Dome Bolt, lining up notches in cap with Dome Ribs. Thread on finial until tight. 9 Owner’s manual and assembly instructions: model 200209 outdoor patio heater 1/15/03 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Endless Summer • i \ Step 9 - Attach Dome to Emitter • Line up holes in dome assembly with the studs from the emitter assembly and lay dome assembly in place. Secure with three nuts. • Place dome cap over center bolt, making sure that the three slots in cap lay over each Rib • Thread on finial until tight. Step 10 - Secure Gas Line • Make sure angled side of Gas Clip pokes up through large hole in Platform. • Tighten screw until Gas Line is held securely in place. • Stand Heater upright. Step 11 - Connect Gas Line to Cylinder The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer. Caution: Before you attempt to use a propane cylinder, understand all cylinder and propane related precautions in Section #1 - “Safety First.” • Slide full Propane Cylinder onto Heater Base. • Attach Gas Line to Cylinder by turning black plastic knob clockwise over Cylinder valve until tight. Note: Be careful not to kink flexible hose of Gas Line. • Secure cylinder in place by attaching loose end of Cylinder Restraint Chain to hole in left leg. Owner’s manual and assembly instructions: model 200209 outdoor patio heater 1/15/03 10 Step 12 - Check for Leaks • Make 2-3 oz. of leak check solution by mixing one part liquid dishwashing soap and three parts water. • Turn cylinder valve ON. • Check Gas Line / Control Valve for leaks: • Spoon several drops of solution onto Gas Line and Control Valve connection. • Inspect the solution at the connection to look for bubbles. • If NO bubbles appear, then the connection is secure. • If bubbles appear, there is a leak - • Turn Cylinder valve OFF. • Loosen screw on Clip. • Release Gas Line fitting from control valve and re-attach making sure connection is secure. (see Step 7) • Retighten Clip. • If you continue to see bubbl...