Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Blue Rhino Dateigröße: 5.93 mb Dateiname: Unterrichtssprache:

Do NOT attempt to assemble without proper tools. (1) Leak Detection Solution (Instructions on how to make solution are included in “Checking for Leaks” section) (1) Precision Filled LP Gas Grill Tank with Acme Type 1 external threaded valve connection (4-5 gallon size) Note: You must follow all steps to properly assemble heater. Typical assembly: approximately 1 (one) hour. Step 1: Unpacking heater Note: When unpacking your heater from the carton, you will find that the engine assembly and the base have been bolted together for shipping purposes. Remove the three nuts at the top of the base and separate the engine from the base. Note: Retain these nuts as you will use them later. Image shown from bottom Step 2: Attach wheel assembly A. Attach wheel assembly to base using 3 sets of small bolt (D), medium lockwasher (M), medium nut (I). B. Tighten bolts once all bolts are in place. 7 Owner's manual: model GWU511A outdoor patio heater Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Step 3: Attach wheel assembly cover A. Attach wheel assembly cover to base using 4 sets of medium screws (B), small lock washers (L), small nut (H). B. Tighten screws once all screws are in place. Step 4: Attach legs A. Attach legs to base using 6 sets of medium bolt (E), medium lockwasher (M), and medium nut (I). Finger tighten only. Note: Do not fully tighten until Step 6. B. Attach small ‘S’ hook on Tank Restraint Chain to left leg. Step 5: Attach weight plate A. Lay base assembly on its side. B. Insert weight plate into base, feet out. Secure using a 9/16” wrench, and 1 set of carriage bolt (G), large lock washer (N), and extra large nut (K). Note: If you plan to anchor your heater permanently, be sure to line up two outer holes in base with those in weight plate so that your anchor bolt will pass through both holes. C. Place base assembly upright. Owner's manual: model GWU511A outdoor patio heater 8 Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Step 6: Attach platform and post A. Attach platform to legs using 7/16” wrench, 3 sets of medium bolt (E), medium lockwasher (M), medium nut (I). B. Attach post to platform using 7/16” wrench, 3 sets of medium bolt (E), medium lockwasher (M), medium nut (I). C. Fully tighten all nuts and bolts from Step 4. TIP: To tighten use a 7/16” wrench on Bolt and a 7/16” socket wrench on Nut. Step 7: Attach shroud cover Slide shroud cover over pole and base assembly until bottom of shroud rests on base. 9 Owner's manual: model GWU511A outdoor patio heater Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Step 8: Attach engine A. Lay engine assembly and base assembly on their side, using carton for support. B. Insert gas line through pole. Note: Make sure gas line comes out bottom of pole before securing engine to pole. C. Attach engine to post using 4 large screws (C). Note: Do not fully tighten screws until all screws are inplace. i Step 9: Attach gas line clip A. Lift shroud cover to expose platform. B. Make sure gas line feeds through indent in gas line clip. C. Attach gas line clip (O) to base platform using 2 medium screws (B), securing the gas line without damaging the exposed bolts. “Oo O O °Oo Oo “Oo o o ü o o O o O on° OOOOOOOOOO ° °0 o O 0 0 o OOO OOO ooo oo o o 0 O o oooooooooo o ° '3 0 0 0 o ooo ooo ooo oo o o g On0® oooooooooo ° °°Q O 0 0 o ooo ooo ooo oo o o o O o n ^noOOu ° 0 00 0 00000000 o w. 0 ° °-°o O O 0 0 0 o ooo 00 o o o ooo ooo o o o o o o o o O Step 10: Connect gas line/regulator assembly Attach gas line/regulator assembly to gas line using 3/4” wrench. Owner's manual: model GWU511A outdoor patio heater 10 Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Step 11: Assemble Dome Note: Each dome section has a pin mounted in the rolled bottom edge. If necessary for proper alignment of dome sections, loosen each screw prior to assembly. A. Slide dome rib onto pin side of dome panel. B. Slide two dome panels togther. Secure with small screw (A). C. Repeat procedure for all three dome panels. D. Insert dome bolt (F) through dome plate, dome, top dome plate, large nut (J). E. Tighten all screws on dome panels. Step 12: Attach dome A. Attach dome to emitter using 3 medium nuts (I). B. Attach dome cap to dome assembly using finial. I Step 13: Insert Battery A. Remove battery cap. B. Insert 1 AA battery (P). C. Replace battery cap. 11 Owner's manual: model GWU511A outdoor patio heater Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Installing LP Gas Tank To operate you will need (1) precision-filled standard grill LP gas tank (20#) with external valve threads. Insert LP Gas Tank Place precision filled LP gas tank into heater base upright so it is arranged for vapor withdrawal. Secure LP Gas Tank Secure tank in place by attaching loose end of tank restraint c...

Herunterladen

Geben Sie zwei Ziffern: