Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Do not return to place of purchase. Owner’s manual: model 200605 outdoor patio heater Assembly Instructions General Components & Features Familiarize yourself with all components before proceeding. Refer to page 5 for hardware and components, and page 21 for specifications. Do NOT attempt assembly unless all components are available. If you believe a component is missing or damaged, contact 1-800-762-1142 for assistance. Note: All hardware is mounted on a cardboard pack and numbered to match their assembly step. Additional Requirements The following items are not included, but are necessary for the proper assembly of your heater. Do NOT attempt to assemble without proper tools. A hex (Allen) wrench is necessary and is included in the parts bag. (1) 7/16” Wrench (1) 9/16” Wrench (1) 7/16” Socket Wrench (1) #2 Phillips Head Screwdriver (1) Leak Detection Solution (Instructions on how to make solution are included in step 12) (1) Precision Filled LP Gas Grill Tank with Acme Type 1 external threaded valve connection (4-5 gallon size) Note: You must follow all steps to properly assemble heater. Note: Unpacking note for 200605 patio heater. When unpacking your heater from the carton, you will find that the engine assembly and the base have been bolted together for shipping purposes. Remove the three nuts at the top of the base and separate the engine from the base. Retain these nuts for use in Step 9. You are now ready to begin assembly of your patio heater. Step 1 – Attach Legs to Base Secure Legs to Base using (2) Small Bolts, (2) Small Lock Washers and (2) Small Nuts per leg. Finger tighten only. Do not fully tighten until Step 2. Attach small ‘S’ hook on Tank Restraint Chain to left leg. Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 2 – Attach Platform to Legs Line up hole in Clip with small threaded hole on bottom of Platform . Attach Clip loosely to Platform with ( ) Large Screw . Note: Do not tighten until step 9 . Using 7/ 6” wrench, secure Platform to Legs using (2) Small Bolts, (2) Small Lock Washers and (2) Small Nuts per Leg Tighten fully . Fully tighten all nuts and bolts from Step . TIP: To tighten use a 7/ 6” wrench on Bolt and a 7/ 6” socket wrench on Nut Step 3 – Attach Weight Plate to Base Lay Base Assembly on its side . Place Weight Plate in Base, feet out . Note: If you plan to anchor your heater permanently, be sure to line up two outer holes in Base with those in Weight Plate so that your anchor bolt will pass through both holes . Insert Carriage Bolt through center holes of Base and Plate . Using 9/ 6” wrench, secure Plate to Base using ( ) Large Lock Washer and ( ) Large Nut . Place Base Assembly upright . Owner’s manual: model 200605 outdoor patio heater Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Owner’s manual: model 200605 outdoor patio heater Step 5 – Attach Engine to Post Lay Engine Assembly on its side, using carton for support. Remove and save Control Knob. Remove and save Engine Access Panel by removing (1) black Thumbscrew from bottom of Access Door. Disconnect wire from Igniter by gently pulling wire from back of box. Align (4) holes in top of Post with (4) holes in bottom of Engine. Note: One hole is at a different level than the rest. Make sure that all 4 holes line up properly. Insert (4) Small Screws enough to hold Engine in place. They will be fully tightened at the end of Step 7. Note: Do not replace Engine Access Panel until Step 13. Step 4 – Insert Gas Line through Platform/Attach Shroud Cover Insert Gas Line up through large hole in Platform from underneath between center and left leg as shown in illustration. Slide Shroud Cover over Gas Line, then over Platform/Leg assembly until bottom of Shroud rests on Base. Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 6 – Attach Engine/Post to Platform Insert end of Post without holes over Gas Line, being careful not to bend Gas Line . Slide Post into collar of Platform so Post rests completely on Platform . Tighten bottom three setscrews with hex (Allen) wrench supplied . Make sure Post is perpendicular to Base . Use top three setscrews to adjust Post’s angle as necessary . Tighten all six setscrews . Note: Post must be perpendicular to Base Failure to do so will adversely affect burner performance . Step 7 – Connect Gas Line to Engine Attach Gas Line to Control Valve: Pull collar of Gas Line back . Insert Gas Line over Control Valve . Release collar and it should lock in place (Tip – push Gas Line up from bottom of Post to make a good seating before releasing the collar ) Gently tug on line to test for proper connection If Gas Line moves it is not properly connected Do not proceed until you have a proper connection . Fully tighten the (4) screws from Step 5 . Owner’s manual: model 200605 outdoor patio heater Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Owner’s manual: model 200605 outdoor patio heater ...