Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
. Remove and save Control Knob. Remove and save Engine Access Panel by unscrewing (1) black Thumbscrew from bottom of Access Door. Disconnect wire from Igniter by gently pulling wire from back of box. Align (4) holes in top of Post with (4) holes in bottom of Engine. Note: One hole is at a different level than the rest. Make sure that all 4 holes line up properly. Insert (4) Small Screws enough to hold Engine in place. They will be fully tightened at the end of Step 9. Note: Do not replace Engine Access Panel until Step 14. Step 8 - Attach Engine/Post to Platform Insert Platform Cover over Gas Line and set on top of Shroud Cover. Insert end of Post without holes over Gas Line, being careful not to bend Gas Line. Slide Post through Cover and into collar of Platform so Post rests completely on Platform. Align the Control Panel with either the right or left leg attached to base. Slide Platform Cover up to expose setscrews in Platform and tighten bottom three setscrews with hex (Allen) wrench supplied. Make sure Post is perpendicular to Base. Use top three setscrews to adjust Post’s angle as necessary. Tighten all six setscrews and slide Cover back down. Note: Post must be perpendicular to Base. Failure to do so will adversely affect burner performance. Owner’s manual: model 235000 outdoor patio heater 6/11/04 9 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. ® Vif-V Endless Summer^: Step 9 - Connect Gas Line to Engine Attach Gas Line to Control Valve: Pull collar of Gas Line back. Insert Gas Line over Control Valve. Release collar and it should lock in place. (Tip - push Gas Line up from bottom of Post to make a good seating before releasing the collar.) Gently tug on line to test for proper connection. If Gas Line moves you are not properly connected. Do not proceed until you have a proper connection. Fully tighten the (4) screws from Step 7. Step 10 - Attach Top Dome to Emitter Gently lay Heater on its side using one styrofoam insert to prop up top half. Align holes in Dome with threaded studs in Emitter brackets. Secure Dome to Emitter using (3) Cap Nuts. Tighten using 13 mm wrench. Stand heater upright. NOTE: The white ceramic cone in the top of the engine is an important piece. DO NOT REMOVE. Step 11 - Secure Gas Line Make sure angled side of Gas Clip pokes up through large hole in Platform. Tighten screw until Gas Line is held securely in place. Stand Heater upright. Section View Owner’s manual: model 235000 outdoor patio heater 6/11/04 10 ® \rf_- Endless Summer^: Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Caution Before you attempt to use a propane cylinder, understand all cylinder and propane related precautions in Section #1 - “Safety First.” Caution Your Endless Summer Portable Heater has been checked at all factory connections for leaks. Recheck all connections, as movement in shipping can loosen connections. Check for leaks even if your unit was assembled for you at the store. Step 12 - Connect Gas Line to Cylinder The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer. • Slide full Propane Cylinder onto Heater Base. • Attach Gas Line to Cylinder by turning black plastic knob clockwise over Cylinder valve until tight. Note: Be careful not to kink flexible hose of Gas Line. • Secure cylinder in place by attaching loose end of Cylinder Restraint Chain to hole in right leg. Step 13 - Check for Leaks • Make 2-3 oz. of leak check solution by mixing one part liquid dishwashing soap and three parts water. • Turn cylinder valve ON. • Check Gas Line / Control Valve for leaks: • Spoon several drops of solution onto Gas Line and Control Valve connection. • Inspect the solution at the connection to look for bubbles. • If NO bubbles appear, then the connection is secure. • If bubbles appear, there is a leak - • Turn Cylinder valve OFF. • Loosen screw on Clip. • Release Gas Line fitting from control valve and re-attach making sure connection is secure (see Step 9). • Retighten Clip. • If you continue to see bubbles after several attempts, contact 1-800-762-1142 for assistance. Check Gas Line / Cylinder valve for leaks: • Turn cylinder valve ON. • Spoon several drops of solution onto Gas Line and Cylinder valve connection. • Inspect the solution at the connection to look for bubbles. • If NO bubbles appear, then the connection is secure. • If bubbles appear, there is a leak: • Turn Cylinder valve OFF. • Release Gas Line fitting from Cylinder valve and re-attach making sure connection is secure (see Step 12). • If you continue to see bubbles after several attempts, contact 1-800-762-1142 for assistance. 11 Turn Cylinder Valve OFF. Owner’s manual: model 235000 outdoor patio heater 6/11/04 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. ® Vif-V Endless Summer...