Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
It is imperative that control compartment, burners and circulating air passageways of the heater be kept clean. • Check heater immediately if any of the following conditions exist: • The smell of gas in conjunction with extreme yellow tipping of burner flames. • Heater does not reach proper temperature. Note: At temperatures less than 40°F, heat output will be reduced. • Heater's glow is excessively uneven • Burner makes popping noises during use. Note: A slight pop is normal when burner is extinguished. • Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times. • Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water. • Do not paint engine, engine access panel or dome. "20 lb.” LP Cylinder Valve Body 18”-19” FOR YOUR SAFETY: Beware of Spiders Spiders or small insects can get into the burner tube or other openings of your heater, and spin webs or build nests. These obstructions can lead to gas flow problems. It is important to make frequent inspections of these areas and clean them when necessary. Before operating your heater for the first time, be sure to check for obstructions that may have occurred during shipment. Need a cylinder or gas? Try Blue Rhino cylinder exchange service. It's easy, fast, safe, and available at tens of thousands of conveniently located retail outlets nationwide. You can purchase a new full cylinder or exchange your empty for a precision filled one. For your nearest Blue Rhino retailer visit Owner’s manual: model 82000 portable outdoor heater 6/11/04 4 Endless Summer- Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Components Part Re-order Name Number Finial ..........56-01-001 Dome Cap......56-01-002 Dome..........56-01-003 Top Wire Guard . .56-01-004 Emitter Assembly .56-01-005 Bottom Wire Guard56-01-006 Post...........56-01-009 Shroud Cover . . .56-01-012 ODS (Oxygen Depletion Shutdown Sensor) 56-01-007 Nozzle.........56-01-017 Valve ..........56-01-018 Control Tilt Switch 56-01-019 Control Knob . . . .56-01-020 Regulator.......56-01-021 Housing........56-01-024 Access Panel . . . .56-01-030 Plastic Ring.....56-01-034 Base .......... 56-01-037 Weight Plate . . . .56-01-041 Extension Hose . .56-01-043 Lock-Up Mount Bracket ........56-01-044 Hardware Picture Qty Description Used in Step(s) I Medium Screw 1 12-24 x 5/16” Stainless Steel Philips Head Screw 56-01-045 Nut 3 1/4-20 Stainless Steel Hex Nut 56-01-046 4 3 5 Owner's manual: model 82000 portable outdoor heater 6/11/04 Endless Summer ^ Assembly Instructions General Components & Features Familiarize yourself with all components before proceeding. Refer to page 5 for hardware and components, and page 18 for specifications. Do NOT attempt assembly unless all components are available. If you believe a component is missing or damaged, contact 1-800-762-1142 for assistance. Note: All hardware is mounted on a cardboard pack and numbered to match their assembly step. Additional Requirements The following items are not included, but are necessary for the proper assembly of your heater. Do NOT attempt to assemble without proper tools. (1) - 7/16” Wrench (1) - #2 Phillips Head Screwdriver (1) - Leak Detection Solution (Instructions on how to make solution are included in Step 7) (1) - 20 lb.(4-5 gallon) precision filled LP Gas Grill Cylinder Note: You must follow all steps to properly assemble heater. Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 1 - Attach Emitter Screen Line up 4 holes on bottom of Emitter Screen with corresponding holes in Emitter Bottom, and insert (4) Medium Screws in holes until tight. Owner's manual: model 82000 portable outdoor heater 6/11/04 6 Endless Summer- Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 2-Attach Top Wire Guard Line up 4 prongs on Wire Guard Bottom with 4 holes on Emitter Bottom, and Insert. Note: It may be necessary to adjust the prongs slightly to line them up with the holes. Step 3-Attach Dome to Emitter Line up three studs in Emitter with holes in Dome. Slide Dome carefully over studs, clamping Top Wire Guard securely in place. Note: It may be necessary to adjust prongs of the Top Wire Guard slightly to provide a secure fit. Install (3) Nuts on studs and tighten with 7/16” wrench. Do not over tighten. Step 4-Attach Dome Cap Lay Dome Cap on Dome covering 3 Nuts and line up center holes. Insert threaded end of Finial through Cap and screw into center of Dome until secure. 7 Owner’s manual: model 82000 portable outdoor heater 6/11/04 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Endless Summer- V Step 5-Center Lockup Slide the threaded portion of the large thumbscrew through the slot in the center of the bracket mounted to the base. Thread the bottom bracket on to the thumbscrew with the rou...