Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation requirements in your area. CAUTION! Read All Instructions Carefully Before Starting The Installation or Operating This Heater. Improper Installation Could Void Your Warranty! US ENVIRONMENTAL PROTECTION AGENCY PHASE II CERTIFIED WOODSTOVE TESTED TO UL 1482 & ULC - S627 Manufactured by: United States Stove Company 227 Industrial Park Road P.O. Box 151 South Pittsburg, TN 37380 Licensed by: Drolet Stoves and Fireplaces Inc. SAVE THIS MANUAL FOR FUTURE REFERENCE THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.E 851573A CONGRATULATIONS! You've purchased a heater from North America's oldest manufacturer of wood burning products. By heating with wood you're helping to CONSERVE ENERGY! Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at least one tree each year. Future generations will thank you. The instructions pertainning to the installation of your wood stove comply ULC-S627 and UL-1482 standards. Combustible : Wood Recommended Surface : 500 to 1,800 ft. (46 to 167m.) Heating Capacity : E.P.A : 30,800 BTU/hr (9.02 kW) Efficiency : 65 % Emissions : 5.7 g/h Colors : Flat Black Flue Pipe Diameter : 6” (152mm) Chimney type : 2 100°F (650°C) Minimum Chimney Hieght : 12’ (3.66m) Maximum Log Length : 19 1/2” (495mm) Dimensions Overall : Combustion Chamber : Width x Depth : Volume : Door Opening : Pyroceram Glass Door : L x W x H 28 . x 25 3/8 x 33 (718 x 645 x 838mm) W x D 18 . x 20 . (464 x 514mm) 3.228 pi. (0.092m.) W x H 9 5/16 x 13 3/8 (237 x 340mm) W x H 12 3/8 x 18 5/8” (314 x 473mm) Weight : 342 lbs (116 Kg) OPTIONS PART NUMBER Thermodisc AC05530 Outside Air Intake Kit AC02080 CAUTIONS: • HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. • DO NOT USE CHEMICALS OR FLUIDS TO IGNITE THE FIRE. • DO NOT LEAVE THE STOVE UNATTENDED WHEN THE DOOR IS SLIGHTLY OPENED. • DO NOT BURN WASTES, FLAMMABLE FLUID SUCH AS GASOLINE, NAPHTHA OR MOTOR OIL. • DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM. • ALWAYS CLOSE THE DOOR AFTER THE IGNITION. 2 Ussc ASSEMBLY Leg Assembly: 1. Remove the firebrick form the unit. Tilt the unit on its side. DO NOT tilt the unit on its back, this could possibly bend or distort the blower chute on the back of the unit. 2. Remove the four(4) Lag Screws holding the two boards to the unit. 3. Mount the legs to the bottom of the unit using the eight bolts, nuts, and washers provided in the parts bag. 4. Carefully stand the unit up onto the legs. Flue Collar Assembly: 1. Mount the flue collar to the top of the unit as shown using the (3) 5/16-18 x 1-1/2 bolts, (3) washers, and (3) weld tabs provided in the parts box. Blower Chute Assembly: 1. Locate the Heat Shield Deflector. Using the three(3) 1/2 Tek Screws provided, mount the deflector to the unit as shown in the diagram. Ash Pan Assembly: 1. Locate the two(2) Ash Pan Supports welded under the unit, then simply slide the ash pan into place under the unit. Replace the Fire Brick as shown in the illustration below. Side view of flue collar mount to heater top Ash PLug Brick Placement Ussc 3 BLOWER ASSEMBLY ASSEMBLY INSTRUCTIONS THE BLOWER ASSEMBLY MUST BE DISCONNECTED FROM THE SOURCE OF ELECTRICAL SUPPLY BEFORE ATTEMPTING THE INSTALLATION. Step 1. Fix the assembly to the back of the stove with the four screws provided. THE BLOWER ASSEMBLY IS INTENDED FOR USE ONLY WITH A STOVE THAT IS MARKED TO INDICATE SUCH USE. DO NOT ROUTE THE SUPPLY CORD NEAR OR ACROSS HOT SURFACES! 4 Ussc INSTALLATION SAFETY NOTICE • IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH. • CONSULT YOUR MUNICIPAL BUILDING DEPARTMENT OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATIONS REQUIREMENTS IN YOUR AREA. • USE SMOKE DETECTORS IN THE ROOM WHERE YOUR STOVE IS INSTALLED. • KEEP FURNITURE AND DRAPES WELL AWAY FROM THE STOVE. • NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR “FRESHEN UP” A FIRE. KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE STOVE. • IN THE EVENT OF A CHIMNEY FIRE, PUSH THE AIR CONTROL FULL CLOSED TO DEPRIVE THE FIRE OF OXYGEN. CALL THE FIRE DEPARTMENT. • DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM. • A SOURCE OF FRESH AIR INTO THE ROOM OR SPACE HEATED SHALL BE PROVIDED WHEN REQUIRED. POSITIONING THE STOVE It is very important to position the wood stove as close as possible to the chimney, and in an area that will favor the most efficient heat distribution possible throughout the house. The stove must therefore be installed in the room where the most time is spent, and in t...