Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
The installation comply with their rulings. Observe closely the clearances to combustibles (page 4). 2. Do not install this heater in a mobile home or trailer. 3. Always connect this heater to a chimney and vent to the outside. Never vent to another room or inside a building. 4. Do not connect a wood burning heater to a Type B gas vent. This is not safe and is prohibited by the National Fire Protection Association Code. This heater requires approved masonry or UL/ ULC Listed Residential Type and Building Heating Appliance Chimney. Use a 6" diameter chimney or larger, that is high enough to give a good draft. 5. Be sure that your chimney is safely constructed and in good repair. Have the chimney inspected by the Fire Department or a qualified inspector. Your insurance company may be able to recommend a qualified inspector. 6. Inspect chimney connector and chimney twice monthly during the heating season for any deposit of creosote or soot which must be removed (see Chimney Maintenance, page 9). 7. Provide air for combustion from outside the house into the room where the heater is located. If the intake is not in the same room, air must have free access in to the room. 8. To prevent injury, do not allow anyone to use this heater who is unfamiliar with the correct operation of the heater. 9. For further information on using your heater safely, obtain a copy of the National Fire Protection Association (NFPA) publication "Using Coal and Wood Stoves Safely" NFPA No. HS10- 1978. The address of the NFPA is Batterymarch Park, MA 02269. ** For more information on a Canadian Installation, obtain a copy of CAN/CSA - B365 - M91 Installation Code for Solid-Fuel-Burning Appliances and Equipment. 10. Disposal of Ashes- Place ashes in a metal container with a tight fitting lid. Keep the closed container on a non-combustible floor or on the ground, well away from all combustible materials. Keep the ashes in the closed container until all cinders have thoroughly cooled. The ashes may be buried in the ground or picked up by a refuse collector. 11. CAUTION- The special paints used on your heater may give off some smoke while they are curing during the first few fires. Build small fires at first. 12. CARING FOR PAINTED PARTS- This heater has a painted jacket, which is durable but it will not stand rough handling or abuse. When installing your heater, use care in handling. Clean with soap and warm water when heater is not hot. DO NOT use any acids or scouring soap, as these wear and dull the finish. PAINT DISCOLORATION WILL OCCUR IF THE HEATER IS OVERFIRED. FOLLOW OPERATING INSTRUCTIONS CAREFULLY. 13. All persons, especially children, should be alerted to hazards from high surface temperatures and kept away while in operation. Small children should not be left unsupervised when in the room with the heater. 14. Keep the area adjacent to the heater free from all combustible materials, gasoline, and other flammable vapors. CAUTION! Do not touch the heater until it has cooled. CAUTION! Do not touch the heater until it has cooled.CAUTION! Do not touch the heater until it has cooled.CAUTION! Do not touch the heater until it has cooled.CAUTION! Do not touch the heater until it has cooled.CAUTION! Do not touch the heater until it has cooled. NOTE: NOTE:NOTE:NOTE:NOTE:NOTE: FOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOT FOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOTFOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOTFOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOTFOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOTFOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOTALREADY INSTALLED. ALREADY INSTALLED.ALREADY INSTALLED.ALREADY INSTALLED.ALREADY INSTALLED.ALREADY INSTALLED. 3 33333 MINIMUM CLEARANCE MINIMUM CLEARANCEMINIMUM CLEARANCEMINIMUM CLEARANCEMINIMUM CLEARANCEMINIMUM CLEARANCE TO COMBUSTIBLE WALLS TO COMBUSTIBLE WALLSTO COMBUSTIBLE WALLSTO COMBUSTIBLE WALLSTO COMBUSTIBLE WALLSTO COMBUSTIBLE WALLS Installation InstallationInstallationInstallationInstallationInstallation Place the heater on solid masonry or solid concrete. When the heater is used on a combustible floor, use an Underwriters Listed floor protector. The floor protector must comply with UL Standards(USA) and CAN/ULC S627(Canada).The base should extend at least 16" beyond the door of the heater and should extend under the flue pipe if it is elbowed towards a wall (Fig. 5). 1. Uncrate and/or unpack the heater, removing all packing material, being careful not to dispose of the Parts Bag. 2. Open the front feed door and remove the parts from inside the stove. You should find the following: Hearth Plate (1); Solid Damper (1); Lids (2); Pivoting Top (1); Lid Support (1); Parts Package (1) containg nuts, bolts, door handle, door latch and securing harware; Legs (4); Cast Iron Collar (1); Cast Iron Damper (1); Baffle Assemb...