Stimmen - 6, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
This fuse cannot be reset, so in the event that the back-up fuse is activated, the heater will need to be replaced. 3 Features of your 2000W Micro Fur..ace heater Electronic thermostat The electronic thermostat works with the external temperature sensor to maintain your selected temperature. It constantly monitors the room’s temperature and continuously varies the heat output to maintain your desired comfort level. Ceramic disc heating system Each ceramic disc contains 1200 honeycomb shaped holes that heat all of the air that passes through them, generating air up to 40% warmer than conventional coil or ceramic chip heaters. External temperature sensor The temperature sensor is located at the rear of the unit, not inside the heater itself, to ensure accurate temperature measurement. It detects even the slightest change in the room’s temperature, and communicates this to the electronic thermostat. Tip over cut-out Should your heater accidentally be knocked over, the instant tip over cut will automatically interrupt power to the heating element and fan. The heater will not resume operation until it is replaced in the upright position. Power/Mode light The power light illuminates amber to indicate that the heater is connected to the power outlet and is set to AUTO mode. It illuminates green when the heater is set to MANUAL mode. 4 Usi..g your heater 1. Place the heater on a flat level surface, approximately 1 metre from any wall or other objects such as furniture, curtains, plants or combustible material, and ensure that the air intake and outlet are clear of obstructions. Note: For most efficient heating, place the heater on the floor where the air is cooler, near an outside door, the bottom of a staircase, or where colder air is most likely to be entering the room. 2. Insert the plug into a 230-240V power outlet and turn the power on. The red power light will illuminate and the screen will display the ambient room temperature. 3. Press the Standby button to select the desired operating mode. Press it once to select the AUTO mode, or twice to select MANUAL mode. 4. In AUTO mode, use the + and – buttons to select the desired temperature. The selected temperature (in degrees celsius) will flash several times to indicate that it is set. The screen will then return to displaying the current room temperature. The thermostat will continue to vary the heat output to maintain your selected temperature. 5. In MANUAL mode, use the + and – buttons to select the desired heat setting, from H1 to H5. The selected setting will flash several times to indicate that it is set. The screen will then return to displaying the room temperature. The heater will operate constantly at the selected heat level, without monitoring the room temperature. 6. To switch between operating modes or turn the heater off, press the standby button. 7. Switch the power off at the power outlet and unplug the heater when not in use. MF2000 Micro Fur..ace Cera..ic Disc Heater 8 3 Year Repdace..e..t Guara..tee We are so co..fide..t of the quadity of our product, shoudd this appdia..ce devedop a..y ..adfu..ctio.. withi.. 3 years of purchase (3 Mo..ths co....erciad use) due to faudty ..ateriads or ..a..ufacture, we widd repdace it for you absodutedy free. Should you experience any difficulties with your appliance, please phone our free call customer service line for advice on 1800 025 059 in Australia, or 0800 786 232 in New Zealand. Alternatively, simply return the faulty appliance to your place of purchase, along with your purchase receipt. Your Sunbeam 3 Year Replacement Guarantee naturally does not cover misuse or negligent handling, and excludes breakables such as glass or ceramic items, and normal wear and tear. Similarly, your 3 Year Replacement Guarantee does not cover damage to household surfaces as a result of water or other substances leaking from your appliance, nor does it cover freight costs. In Australia, this guarantee is additional to the conditions and guarantees which are mandatory as implied under the Trade Practices Act 1974 and State and Territory legislation. Sunbeam Service Centres Sunbeam has established a network of authorised service centres throughout Australia and New Zealand to provide quick, convenient service for our customers. Should your appliance require repair or service, either during or after the guarantee period, contact your nearest service centre. For a complete list of Sunbeam’s authorised service centres: Australia centres 1800 025 059 New Zealand centres 0800 786 232 Co..su..er Hotdi..e I.. Austradia Visit Or cadd 1800 025 059 I.. New Zeada..d Visit Or cadd 0800 786 232 is a registered Trade..ark of Su..bea... is a registered trademark of Pelko Electric Company and is used under licence by Sunbeam Corporation Limited. Made i.. Chi..a. Due to ..i..or cha..ges i.. desig.. or otherwise, the product ..ay differ fro.. the ...
Dieses Handbuch ist für folgende Modelle:elektrische Heizungen - MF2000 2000W (1.56 mb)