Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Cadet Dateigröße: 176.87 kb Dateiname: cadet-uc101b.pdf Unterrichtssprache:

Failure to do so could 8. WARNING Fire or explosion may occur. Heater has hot and arcing or sparking parts inside. Do not install heater in any area where combustible vapors, gases, liquids, or excessive lint or dust are present. Features & Benefits • Thermal Safeguard • High temperature manual reset: turns off heater if normal operating temperatures are exceeded • Rugged steel-finned element • Ideal for bathrooms and kitchens • Low profile for rooms with limited space • Two-year extended warranty • Single pole or double pole field mount thermostat kit available • Black or white powder coat paint fora durable finish MODELS The Perfectoe UC072 UC102 UC101 * For installations above 7000 feet, highest wattage recommended is 750 watts. TOOLS REQUIRED: Phillips Screwdriver Straight ScrewdriverWire Strippers Utility Knife (2) 11/2” Wood Screws (3) Insulated Wire Connectors(1) Strain Relief Connector 18” 45.7cm 14.” 36.8cm 3.” 8.9cm 8.” 21cm .” .6cm Front Top Side result in serious electrical shock, burns, or possible death. 1. Read all instructions before using this heater. 2. Read all information labels. Verify that the electrical supply wires are the same voltage as the heater. 3. All electrical work and materials must comply with the National Electric Code (NEC), the Occupational Safety and Health Act (OSHA), and all state and local codes. 4. Connect the grounding pigtail (copper wire) provided in the wall can to the supply ground wire. 5. If you need to install a new circuit or need additional wiring information, consult a qualified electrician. 6. Protect electrical supply from kinks, sharp objects, oil, grease, hot surfaces or chemicals. 7. WARNING Overheating or fire may occur. DO NOT install the heater in a floor, behind doors, or outdoors. 9. WARNING Burn Hazard. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use extreme caution when any heater is used by or near children or invalids and whenever the heater is left operating unattended. 10. WARNING Risk of Electrical Shock. Keep all foreign objects out of heater. Do not operate after heater malfunctions or has been dropped or damaged in any manner. 11. WARNING Risk of Fire. Do not block heater. Heater must be kept clear of all obstructions: a minimum of 3 feet in front, 6 inches on both sides. Heaters must be kept clean of excessive lint, dirt and debris. (See Maintenance Instructions). 12. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. SAVE THESE INSTRUCTIONS Tel: 360-693-2505 P.O. Box 1675 Vancouver, WA 98668-1675 READ ALL INSTRUCTIONS AND SAFETY INFORMATION IMPORTANT! It is extremely important that you verify the electrical supply wires are the same voltage as the heater (i.e. 120 volt heater to 120 volt power supply and 240 volt heater to 240 volt power supply). If replacing an existing heater, check the labels of the old heater and replace using the same voltage. Hooking a 240 volt heater to a 120 volt power supply will drastically reduce the heater’s output. Hooking a 120 volt heater to a 240 volt power supply will destroy the heater. Connecting your heater to an incompatible power supply will void the warranty. Installation Instructions Part One PLACEMENT: Read IMPORTANT INSTRUCTIONS for important safety requirements. For best results, install heater beneath a cabinet in the toe kick area. Install the Perfectoe (Model UC) horizontally. Do not install the UC heater in the floor. Headers and bracing are not necessary. Heater must be installed per the directions indicated on the lid. See clearance requirements for additional placement instructions. Install at least 6” from the inside corner and/or vertical adjacent surfaces. CONTROLS: A thermostat is required. A Cadet electronic thermostat is recommended for ultimate control and comfort. Optional single or double pole field mount thermostat kits are also available. STEP 1 Turn the Electrical Power OFF Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel board door to prevent someone from turning on power while you are working on the heater. STEP 2 Determine Area of Installation The UC Series heater REQUIRES A MINIMUM distance of 6 inches from adjacent surfaces (See Figure 1). However, Cadet RECOMMENDS 12 inches from all adjacent surfaces for longer and cleaner performance. Heaters must be spaced at least 3 feet apart. For installation in an existing wall/cabinet, cut a rough opening 14. inches wide by 3. inches high. Opening must be 8. inches deep and 6 inches from adjacent wall. Figure 1 WARNING! Vinyl floor manufacturers warn that some vinyl may discolor from temperatures in excess of 110° F. See your vinyl floor manufacturer for temperature specifications for your vinyl floor covering. STEP 3 Route Supply Wires For wall thermostat applications, route supply wire from circ...

Herunterladen

Geben Sie zwei Ziffern: