. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 3. Operation Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Performing a Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Self-Test Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Specifications for Frequency and Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1992-2005 Manual Part Number: E1445-90011 Printed: November 2005 Edition 2 Printed in U.S.A. E1105 Contents Chapter 1 - General Information Introduction................................................................................9 Safety Considerations......................................................................10 Warnings and Cautions ................................................................10 Inspection/Shipping........................................................

Adjust your Spectrum Analyzer as necessary. 1. Reset the AFG: *RST ;*CLS Reset AFG and clear status registers 2. Set the AFG to output a -5 dBm, 10 MHz sinewave with the 10 MHz filter enabled: FREQ 1.0E7; Set AFG frequency :VOLT -5DBM Set AFG amplitude OUTP:FILT:FREQ 10 MHZ Set filter to 10MHz OUTP:FILT ON Enable filter INIT:IMM Initiate waveform Agilent E1445A Service Manual Verification Tests 69 Test 2-10: Spurious/Non-Harmonic Distortion (cont’d) Test Procedure (cont’d) Perform

Use a Root Nyquist filter when you want to place half of the filtering in the transmitter and the other half in the receiver. The ideal root-raised cosine filter frequency response has unity gain at low frequencies, the square root of raised cosine function in the middle, and total attenuation at high frequencies. The width of the middle frequencies is defined by the roll off factor or Filter Alpha (0 < Filter Alpha < 1). • Nyquist is a raised cosine pre-modulation FIR filter. You can use a Nyqu

Chapter 2 Basic Operation Configuring the RF Output Configuring a Ramp Sweep for a Master/Slave Setup This procedure shows you how to configure two PSGs and an 8757D to work in a master/slave setup. 1. Set up the equipment as shown in Figure 2-7. Use a 9-pin, D-subminiature, male RS-232 cable with the pin configuration shown in Figure 2-8 on page 46 to connect the auxiliary interfaces of the two PSGs. You can also order the cable (part number 8120-8806) from Agilent Technologies. By connecting t

Differential data encoding can be described by the following equation: transmittedbit i()= databit i( –1).databit i() For a bit-by-bit illustration of the encoding process, see the following illustration: 0 101 00 1 100 101 raw (unencoded) data change = no change = 1111010101111 differentially encoded data 162 Chapter 7 Custom Real Time I/Q Baseband Working with Differential Data Encoding How Differential Encoding Works Differential encoding employs offsets in the symbol table to encode user-def

Compare the print date of this guide (see bottom of page) with the latestrevision, which can be downloaded from the following websites: Manufacturing Part Number: E8251-90355 Printed in USA February 2008 © Copyright 2006-2008 Agilent Technologies, Inc. Notice The material contained in this document is provided “as is”, and is subject to being changed, without notice, in future editions. Further, to the maximum extent permitted by applicable law, Agilent disclaims all warranties, either express o

Before running the program: • Connect the output of a modulating signal source to the signal generator’s EXT 2 input connector. • Set the modulation signal source for the desired FM characteristics. Agilent N518xA, E8663B, E44x8C, and E82x7D Signal Generators Programming Guide Programming Examples GPIB Programming Interface Examples Launch Microsoft Visual C++ 6.0, add the required files, and enter the code into your .cpp source file. visaex5.cpp performs the following functions: •error checking

140: Opens an IO path for sending binary data to the signal generator. 150: Creates an ASCII string representation of the number of bytes in the waveform. 160 to 170: Finds the number of digits in Nbytes. 190: Sends the first part of the SCPI command, MEM:DATA along with the name of the file, data_file, that will receive the waveform data. The name, data_file, will appear in the signal generator’s memory catalog. 200 to 210: Sends the rest of the ASCII header. 230: Sends the binary data. Note th