Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Baldor Dateigröße: 2.26 mb Dateiname: Unterrichtssprache:

=>4)$) -)/ -)2 )' -)3 3- . v ?3 -) - $ 33 $& 2) )$ 33 $3. =>4)$) -)/ -)2 )' -)& 2 3. ^. " - -) - - $ 33 $& 2) )$ 33 $3. =>4)$) -)/ -)2 )' -)& 2 3. >. -) --'2 ) $))- -3 -$ 33 $3-) 3+. =>4)$) -)/ -)2 )' -)3 3- . '!4$5/. 5) -) - 3 - - $ - )$ +4)$ 2 - -(& $. -) 2' - &+ & - & ) -3+4)2 2( )'. 3 -, . '!&/. <2)). -2 ) - -- )$ $ -. 4$5/. 5) -) -- -- $ )$ -)$ . &/. <2))<2 ) - --)$ . MN2407 Operation 4-0 Operator Control Panel Continued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perating Procedures!The engine.generator controller is designed to start and stop an engine from either a local! (.Manual.) or remote (.Automatic.) modes. When a start command is issued, the controller! issues a run and crank output signal. The controller then monitors engine speed and when crank! disconnect speed is reached, the crank signal is terminated. While the engine accelerates to! normal speed, the controller continuously monitors the engines speed signal. Should the engine! speed exceed the maximum predetermined setpoint, the overspeed shutdown fault circuit will! activate, terminating the run signal In addition to overspeed shutdown, the engine controller also monitors many other engine! protection circuits and should they be activated, the engine will be stopped and/or alarm initiated The engine will automatically stop for any shutdown condition, or when the remote and/or local! start signal is removed. The engine controller operation includes time delay circuits for normal! operating conditions such as start delays, cool down and cranking periods Manual Start/Stop! To manually Start the Gen.Set, push the .RUN. push.button. The following happens:! 1.When the .RUN. push.button is pressed, an ENGINE START DELAY timer is initiated( The start sequence will not be initiated if any shutdown fault condition is present.)! 2.When the engine start delay time expires, an engine RUN and CRANK output signal! will be initiated. (The RUN output may be programmed to only energize when a start! signal is initiated and an engine speed signal is detected.)! 3.When the engine starts and begins to accelerate to nominal speed, the controllers! speed sensor will terminate the CRANK output when engine speed reaches! approximately 20% speed (i.e. CRANK DISCONNECT speed setpoint). Immediately! upon reaching crank disconnect speed, the controller will initiate the BYPASS DELAY! time delay function. After the BYPASS DELAY time period (typically 10 seconds) all! fault circuits programmed as BYPASS DELAY=YES are active. (All fault circuits! programmed as BYPASS DELAY=NO are continuously armed irrespective of any! operation sequence.)! To manually Stop the Gen.Set, push the .OFF. push.button. The controllers RUN output will be! immediately terminated which will initiate the engine stop sequenceAutomatic Start/Stop ! To setup the generator for automatic operation, pressing the .AUTO. push.button. ! The following happens:! 1.The engine will automatically start upon activation of the remote start contact input. The! remote device initiates a start sequence upon contact closure2. When the remote start signal is activated, the engine will start as per the sequence of! operation described for the manual start sequence 3.The automatic stop sequence will be initiated by removal of the remote start signal 4.When the start signal is removed, a cool down delay function will be initiated 4-2 Operation!MN2407 5.When the cool down time delay period expires (typically 5 minutes), the controllers! RUN output will be immediately terminated which will initiate the engine to stop Automatic Fault Shutdown! When a fault circuit is programmed as a SHUTDOWN, the engine will immediately stop when the! fault is activated. A specific shutdown fault can be programmed with a definite time transient! delay period that must expire before the shutdown is activated. The stop sequence will cause the! controllers RUN output to be immediately terminated which will cause the engine to stop. This! will prevent subsequent operation of the generator set. The Run/Stop/Auto selector switch on the! operator control panel must be momentarily placed in the .Stop. position to reset the fault Automatic Mains Failure (AMF)! Figure 4-2 Auto Mains Failure (AMF) Connections ! MN2408!Operation 4-2 When the control...

Herunterladen

Geben Sie zwei Ziffern: