Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Armstrong World Industries Dateigröße: 2.52 mb Dateiname: Unterrichtssprache:

. Never use metallic objects on the neck or hands when handling the set. . Never connect the negative terminal from the battery to the positive terminal from the starter. . Don‘t smoke or allow sparks, flames or other sources of ignition around the fuel or bat- teries. . Use adequate equipment to take fuel from the set. . Never test the battery by touching together the terminals. . Ensure the generating set room is properly ventilated. . Don‘t touch the battery charger or the connections during the battery charging process. . Always disconnect the negative terminal from the battery before to start any work on the unit. . Keep the room, the floor and the generating set clean. When spills of fuel, oil, battery electrolyte or coolant occur they should be cleaned up immediately. . Never store flammable liquids near the engine. . Store oily rags in covered metal containers. . Avoid refilling the fuel tank while the engine is running. . Do not attempt to operate the generating set with any known leaks in the fuel system. 4. INSTALLATION, HANDLING AND TOWING . Make electrical connections in compliance with relevant electrical codes, standards or other requirements. This in- cludes requirements for grounding and ground/earth faults. . For stationary generating sets with remote fuel storage systems, make sure such systems are installed in compliance with relevant codes, standards or other requirements. . Engine exhaust emissions are hazardous to personnel. The exhaust for all indoor generating sets must be piped out- doors via leak-free piping in compliance with relevant codes, standards and other requirements. Ensure hot exhaust silencers, piping and turbochargers, if equipped, are clear of combustible material and are guarded for personnel protection per safety requirements. Ensure that fumes from the exhaust outlet will not be hazard. . Never lift the generating set by attaching to the engine or alternator lifting lugs. Use a sling with a .spreader bar. connected to the base frame. . Ensure the lifting rigging and supporting structure is in good condition and has capacity suitable for the load. . Keep all personnel away from the generating set when it is suspended. . Make sure all personnel are out of the generating set canopy or container, if equipped, before closing and latching enclosure doors. . When towing a mobile generating set, observe all codes, standards or other regulations and traffic laws. These in- clude those regulations specifying required equipment and maximum and minimum speeds. Ensure brakes, if fitted, are in good order. . Do not permit personnel to ride in or on the mobile generating set. Do not permit personnel to stand or ride on the drawbar or to stand or walk between the generating set and the towing vehicle. . Do not install or use the generating set in any classification of hazardous environment unless it has been specifically designed for that environment. Page 7 5. MECHANICAL The generating set is designed with guards for protection from moving parts. Care must still be taken to protect personnel and equipment from other mechanical hazards when working around the generating set. . Do not attempt to operate the generating set with safety guards removed. While the generating set is running do not attempt to reach under or around the guards to do maintenance or for any other reason. . Keep hands, arms, long hair, loose clothing and jewellery away from pul- leys, belts and other moving parts. Attention!! Some moving parts con not be seen clearly when the set is running. . Keep access doors on enclosures, if equipped, closed and locked when not required to be open. . Avoid contact with hot oil, hot coolant, hot exhaust gases, hot surfaces and sharp edges and corners. . Wear protective clotting including gloves and hat when working around the generating set. . Do not attempt to remove the radiator filler cap until the coolant has cooled. Then loosen the cap slowly to relive any excess pressure before removing the cap completely. . Ethyl ether starting aids must not be used on engines with combustion air preheating devises. These starting aids will reduce the efficient working life of the engine. 6. CHEMICAL Fuels, oils coolants, lubricants and battery electrolyte used in this generating set are typical of the industry. However they can be hazardous to personnel if not treated properly. . Do not swallow or have skin contact with fuel, oil, coolant, lubricants and battery electrolyte. If swallowed, seek medical treatment immediately. Do not induce vomiting if fuel is swallowed. For skin contact, wash with soap and water. . Do not wear clothe that has been contaminated by fuel or lube oil. . Wear an acid resistant apron and face shield or goggles when servicing the battery. If electrolyte is spilled on skin or clotting, flush immediately with large quantities of water. . Always keep good ventilation when the equipment is working. Carbon Monoxide inhalation cause death. Always maintain inspecti...

Herunterladen

Geben Sie zwei Ziffern: