Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Do not return the clipper to the charger base with the motor switch in the “ON” position. If the clipper is accidentally put on the charger base in the “ON” position, remove it promptly. Turn clipper off and return to the charger base. 2. Do not insert anything metallic into the battery pocket of the charger base (Diagram C). 3. Do not attempt to charge any other battery other than the battery pack designed for your Andis AGR+ Clipper. 4. Do not store battery or charger where it is under 50°F or over 104°F, as damage may occur (Diagram D). 5. Do not expose the charger base or the battery pack to excessively damp conditions (Diagram E). 6. Avoid dropping the charger base and the battery pack. Do not attempt to use a damaged battery pack or charger. 7. Clean external parts of charger with a soft brush or damp rag. Do not use harsh abrasives, detergents, or solvents (Diagram F). GUIDELINES FOR BATTERY PACK AND CHARGER USE 1. Your clipper, battery pack, and charger function as several interacting electrical systems. Good electrical contact must be maintained in order for the motor to deliver full power and the battery to charge properly. Limited or erratic performance caused by dirt or age can be restored in the majority of the cases if you do the following: A. Problem: Clipper motor starts and stops as if there was a loose electrical connection. Solution: Remove the battery pack from the clipper. Examine the battery pack opening in the clipper. Locate the two sets of motor contacts. Gently squeeze the metal leaves until they are about 1/16 apart using a long pliers or similar. DO NOT squeeze the metal leaves completely together or the battery pack will not re-insert. B. Problem: Charger does not fully charge the battery. Solution: Clean the battery pack bottom contacts (the portion inserted into the charging pocket). Clean the charger contacts. Re-align the charger contacts. To clean the battery pack contacts, rub gently with a pencil eraser until they are brightly polished. Use a cotton swab and 91% isopropyl alcohol to remove any residue or dirt. Denatured alcohol can also be used. Use care, as both products are flammable. Clean the charger contacts in the same way UNPLUG CHARGER FIRST. Make sure eraser dust and cleaners do not get inside the charger base. To re-align the charger contacts, again make sure it is unplugged, and gently pull the metal loops on the four contacts forward SLIGHTLY. Do not severely bend, deform, or damage the contacts. C. Problem: Charger lights flash on and off as clipper or battery is moved side to side in the charger pocket. Solution: Re-align the charger contacts as noted above. 2. To increase the life of your battery pack, do not run the clipper until the motor completely stops. When the motor noticeably slows during clipping where it did not before, charge the battery pack. 3. A new battery pack may not charge to full capacity on the first use. This is normal and does not indicate a problem with the battery pack or charger. About five cycles of using the clipper until the motor slows, and then recharging it will bring the battery pack to full capacity. This is called “forming” a battery pack. 4. It is normal for the charger to become warm to the touch during operation. 5. Disconnect the charger from the AC outlet if long periods of non-use are anticipated. 6. Never store batteries in a discharged condition. Recharge them immediately after they are discharged. 7. Many factors influence the life of the battery pack. A battery pack that has received heavy use and is over a year old, may not give the same run-time performance as a new battery pack. • By using the included car adapter, you can operate your Model AGR+ charging stand within a motor vehicle that is equipped with a 12V power outlet (lighter adapter). car adapter operating instructions 1. Remove power cord from back of charging stand. 2. Plug car adapter cable into back of charging stand. (Diagram G) 3. Insert the car adapter into the 12V power outlet (cigarette lighter adapter) in your car. The green light on the car adapter will turn on to indicate that the adapter is plugged in. Diagram B BatteryFast ChargeChargingMODEL AGSIZE 10/1.5mm Diagram C Diagram D Diagram E Diagram F 3 Car Adapter for Model AGR+ Charging Stand (included) Plugs into charging stand Indicator light Plugs into 12V power outlet 4 4. Refer to previous section "Model AGR+ Battery and Charging Stand" for directions on charging the AGR+ clipper. Note: If car adapter cable fails to work, the fuse may need to be replaced. You can purchase a 500mA fuse at an electronic store. To remove fuse, unscrew cap on car adapter cable (Diagram H). Use your thumb and forefinger to pull fuse out of adapter (Diagram I). To replace, set one end of the new fuse into the opening in the adapter. Use your thumb to press fuse straight into the opening in the car adapter. Replace cap. If your car adapter cable still fails to work you will need to contact the nearest Andis Se...