Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Do not use compressed air, abrasives, scourers or liquids such as acetone to cleanthe razor. Cleaning the Shaving Unit The razor heads may be quickly cleaned after each use by rinsing with hot water:Water from the tap should be on a hot setting, BUT BE CAREFUL TO TEST WATER FIRST SO AS NOT TO BURN OR SCALD HANDS. . Regular cleaning guarantees better shaving results. . Do not immerse razor in water. . While rinsing razor heads, water may drip out of the base of razor. This is a normal occurrence. 1 C 2 Always turn razor OFF, unplug from outlet and remove power cord from razor. Press the Razor Head Release Button to open the Razor Head Assembly. C 3 Clean inside razor heads and hair chamber by running under hot water. C 4 ENGLISH 17 Clean outside of Razor Head Assembly by running under hot water. 5 Close the Razor Head Assembly and shake off excess water. Be careful not to hit the shaving unit against anything while shaking off excess water. 6 Open Razor Head Assembly again and leave open to air dry. NOTE: Do not wipe or dr y the shaving heads with a towel or tissue.This could damage the shaving heads. . If the shaving unit becomes detached from the razor, you can easily reattach it. . You may also clean the hair chamber without water by using the supplied brush. Extra-thorough Cleaning Method Do not mix up the cutters and combs as the shaving performance may be adversely affected for several weeks before optimal shaving performance is restored. 1 Turn razor OFF, remove the charging plug from the outlet and power cord from the razor. ENGLISH C 2 Press the Razor Head Release Button to open the Razor Head Assembly. C 3 Pull the shaving unit off the razor. C 4 Turn the lock counterclockwise to unlock (1) and remove the retaining frame (2). C 5 Remove and clean one set of cutters and combs at a time. C 6 Separate the cutter from the comb and clean it with the brush supplied. Do not clean more than one cutter and comb at a time, since they are all matching sets. If you accidentally interchange the cutters and combs, it could take several weeks before optimal shaving performance is restored. 18 ENGLISH C 7 Clean the inside and outside of the comb with the brush supplied. For optimum performance, razor cutters and combs should be cleaned in a degreasing liquid (e.g. Philips Norelco Shaving Head Cleaning Spray, Model HQ110 or alcohol) and lubricated with one drop of mineral oil (in the center of the head). This helps prevent wear of the shaving heads. C 8 Replace the set back into the Razor Head Assembly. C Make sure that the two pointy edges of the head fit exactly into the recesses. 9 Repeat the process for the other two sets of cutters and combs. 10 Replace the frame and turn the lock clockwise until it locks into place. C 11 Insert the notch of the shaving unit into the slot in the top of the razor (1) and then close the shaving unit (2). NOTE: If the shaving unit does not close smoothly, make sure you inserted the shaving heads properly and that the retaining frame is locked. 19 2 1 1 2 ENGLISH After Each Use: Trimmer 1 Turn razor OFF. C 2 Push down spring-release trimmer switch. C 3 Clean trimmer with the short-bristled side of the brush every time you use it. C 4 Lubricate the trimmer teeth with one drop of mineral oil every 6 months. 5 Close trimmer by pressing trimmer down. Replacing the Razor Heads Replace the razor heads once a year for optimal shaving results. Replace damaged or worn razor heads with model HQ8 Philips Norelco razor heads only. 1 Turn razor OFF, remove the charging plug from the outlet and power cord from the razor. 20 ENGLISH C 2 Press the Razor Head Release Button to open the Razor Head Assembly. C 3 Pull the shaving unit off the razor. C 4 Turn the lock counterclockwise to unlock (1) and remove the retaining frame (2). 5 Remove the razor heads and place the new razor heads in the shaving unit. C Make sure that the two pointy edges of the head fit exactly into the recesses. 6 Replace the frame and turn the lock clockwise until it locks into place. C 7 Insert the notch of the shaving unit into the slot in the top of the razor (1) and then close the shaving unit (2). NOTE: If the shaving unit does not close smoothly, make sure you inserted the shaving heads properly and that the retaining frame is locked. This razor has no other user-serviceable parts. For assistance call 1-800-243-3050 21 2 1 1 2 22 ENGLISH C . Put the Protective Cap on razor to protect heads. . Be sure razor is turned off. Remove cord from outlet and razor before storing in a safe, dry location where it will not be crushed, banged, or subject to damage. Storage . Do not wrap power cord around razor when storing. . Store cord in a safe location where it will not be cut or damaged. . Do not place or store razor where it can fall or be pulled into a tub or sink, water or other liquid while plugged in. Assistance . For assistance, visit our website: or call toll free 1-800-243-3050 . Online informat...