Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
You can use this watertight shaver in the shower and clean it in water. Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic WET/DRY shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method. Charge the shaver for at least 8 hours before using it for the first time or when it has not been in use for more than six months. Parts identification (see fig. 1) ® Protective cap (в) System outer foil release buttons © Foil frame ® System outer foil (D Inner blade © Foil frame release button © On/Off switch (0) Switch lock button 0 Battery capacity monitor. (j) Charge status lamp ® Trimmer © Trimmer switch <0> Charging adaptor with automatic voltage adjustment ® Wall mount © Wood screws How to use the wall mount The charging adaptor can be hung on the wall using wood screws (included). 1. Select an appropriate location on the wall where the screws can go in. 2. Attach the wall mount to the wall as shown with the wood screws, making sure that the arrow points up. 3. Slide the charging adaptor grooves into the wall mount until it clicks in. To remove the charging adaptor from the wall mount, slide the adaptor upward. Charging (see fig. 2) Place the charging adaptor upright on a flat surface or mount it on a wall. Plug the adaptor into an AC outlet. It will adjust automatically to voltages between 100-120 and 220-240V AC. Do not recharge the shaver from the SHAVERS ONLY outlet (AC220-240V) which is usually in hotel bathrooms in European and Asian countries as it will damage the charging adaptor and/or outlet. In some areas, a special plug adaptor may be required. Switch the shaver to the “0 • charge” position and place it upright into the charging adaptor with the switch facing toward the front. The charge status lamp will glow red when the shaver is placed on a right charging position. It will turn to green when the charging is completed (see fig. 2A). At the same time, the battery capacity monitor will display the fully charged condition (see fig. 2A). You can fully charge the shaver in one 6 hour if the battery capacity monitor flashes down to the 20% level (see fig. 2B). A full charge will supply enough power for about 14 shaves (three minutes per shave for a normal beard). You can always store your shaver in the charging adaptor to maintain full power capacity. This shaver cannot be overcharged. Before traveling, charge it fully for 1 hour if you will not be taking the charging adaptor with you. In case your shaver is discharged, you may quick charge it for one shave in about five minutes. For a better shave {see fig. 3) Put a thin layer of shaving foam on your face which works as lubricator. Do not put a thick layer of shaving foam as it becomes messy. If the shaving head is clogged with foam, simply rinse it under running water. Hold the shaver at a right angle (90°) to your skin. Depress the switch lock button and slide the On/Off switch upward to turn the shaver on. Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave and may irritate skin. System outer foil and lift strips (see fig. 4) The system outer foil has a slit blade a) between two foils (b), and lift strips c) on each outside of the foils. They move up and down independently to follow the contours of your face. The lift strips lift lying hairs and help introduce the hairs into the holes of foils to cut. The slit blade catches and cuts longer and lying hairs easily. Using the trimmer (see fig. 5) Slide the trimmer switch up to the fftwi position until it clicks in. Place the trimmer at a right angle to your skin and move it downward to trim sideburns. Cleaning your shaver (see fig. 6) After every shave, press the foil frame release button to pop open the foil frame. Turn the shaver on and rinse the inner blade under running water or in a basin. After rinsing, switch the shaver off and leave it to dry without closing the foil frame and the protective cap. After the shaving head dries, close the foil frame and replace the protective cap on the shaver. Replacing shaving head components With daily use, and depending on the thickness of beard, the outer roil may need to be replaced every year and the inner blades every 2 years. 7 Replacing the system outer foil (see fig. 7) Squeeze the system outer foil release buttons and lift the system outer foil upward to remove it. To insert the new system outer foil, press down until it snaps into place. Replacing the inner blades (see fig. 8) Press the foil frame release button to pop open the foil frame. Pull the foil frame vertically out of the upright shaver. Remove the inner b...