Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
You can use this watertight shaver in the shower and clean it in water. The following is the symbol of Wet shaver. The symbol means that hand-held part may be used in a bath or shower. Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic Wet/ Dry shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method. Parts identification (see fig. 1) A Protective cap B System outer foil C System outer foil release but tons D Foil frame E Inner blades F Foil frame release buttons G Pivot action selector H LED display I Battery capacity monitor I-a high I-b mid I-c low 6 J Charge status lamp K Low battery indicator L On/Off switch M Finger rest N Trimmer O Trimmer handle P Adaptor Q Power cord R Charging stand READ ALL INSTRUCTIONS BEFORE USE. Charging Connect the power cord to the shaver, and plug the adaptor into an AC outlet. (see fig. 1 (A)) The shaver will adjust automatically to voltages between 100-240V AC. In some areas, a special plug adaptor may be required. • When charging the shaver for the first time or when it has not been in use for more than 6 months, the charge status lamp may not illuminate for a few minutes after operation. It will eventually illuminate if kept connected. Adequate ambient temperature for charging is between 15 ° C (59 ° F) to 35 ° C (95 ° F). • If it is far below or over the appropriate temperature, the charging time may be longer, or the adaptor may not function. • In particular, low temperature may shorten the life span of the rechargeable battery. In this case, the 7 charge status twice second. [for ES8048, ES8044] The charge status lamp when the shaver is being charged. The battery capacity monitor will fully illuminate and the charge status will blink after charging is completed (see fig. 2 (A)). 10 minutes after charging is completed, the battery capacity monitor will turn off and the charge status lamp will continue to blink (see fig. 2 (B)). You can fully charge the shaver in 1 hour if the LED display shows “ low” . The battery capacity monitor indicates the charge remaining in the battery in 3 levels (high/mid/low). The unit can be used once or twice more after “ low” starts to blink (Differs depending on usage.). [for ES8043] The charge status lamp will glow when the shaver is being charged. It will blink when charging is completed (see fig. 2 (D)). You can fully charge the shaver in 1 hour if the low battery indicator blinks (see fig. 2 (C)). The unit can be used once or twice more after the low battery indicator starts to blink. [for ES8042] The charge status lamp will glow when the shaver is being charged. It will blink when charging is completed (see fig. 2 (E)). A full charge power for approx. 14 shaves (3 minutes per shave for a normal beard). Before travelling, charge your shaver fully for 1 hour if you will not be taking the adaptor with you. In case your shaver is without charge, you may quick charge it for 1 shave in about 5 minutes. Charge with charging stand (see fig. 1 (B)) To charge with the charging stand, connect the power cord to the charging stand. Place the shaver into the stand, and plug the adaptor into the AC outlet. You can always store your shaver in the charging stand to maintain full battery capacity. This shaver cannot be overcharged. Using your shaver Caution – The system outer foil is very thin and can be damaged if handled improperly. Before each use, always check the foil for damage. To avoid personal injury, do not use if the foil or other parts of the shaving head is damaged. Disconnect the power cord from the shaver, and push the On/Off switch to turn the shaver on. 8 If you push and switch for more than 2 it will activate the turbo mode “ sonic” vibration cleaning. (see “ Cleaning your shaver” ) Caution: Shaving with “ sonic” vibration may damage your skin. Please turn it off and on again to deactivate the turbo mode. Do not place fingers on the On/Off switch during use. This may cause the shaver to stop during use or change to the “ sonic” vibration cleaning mode. Place your finger on the finger rest during use. Hold the shaver at a right angle (90° ) to your skin (see fig. 3). Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. Pivot action selector (see fig. 4) Use the pivot action selector to choose the shaving mode, “ soft” and “ lock” based on your shaving preference. The pivot action can be changed whether the switch is turned on or off. System outer (see fig. 5) System outer foil has a slit blade (a) between 2 foils (b). They move up and down independently to the contours of your face. The slit blade catches and cuts longer and lying hairs easily. For w...