Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
2 345 selectstatuschargedryclean6 66 Press[select]toselectthecourse. 2 22 Plug in the adaptor. • Remove any soap or water on the shaver if it has been washed with hand soap or any other detergent. 3 33 Pull up the arm. 4 44 Remove the protective cap . and then attach the shaver. • Turn the shaver off before attaching. • Check that the outer foil is not deformed or damaged when you are attaching the shaver. 5 55 Push down the arm. • Each time you press [select], the course changes from “Clean/Dry/Charge” . “Clean/Dry” . “Dry/Charge” . “Dry” . “Charge”. • The courses start approximately 6 seconds after they are selected. • The course will be aborted if the power is cut off. In this case, perform the course again from the beginning. • Do not detach the detergent cartridge or the water tank as the cleaning liquid may spill causing a malfunction. Course CourseselectionindicationsOn shaver . CoursecompletionsummaryOn recharger Changeable course halfway through On recharger On shaver Time required (guide)clean dry charge clean dry charge 1Charge * 2345Glows .Blinks 1 hour 2Clean/Dry/ Charge 3Glows while charging .Blinks 4 h 30 min 3Clean/Dry 2– .– 3 hours 4Dry/Charge 235Glows while charging .Blinks 4 h 0 min 5Dry 234– .– h 50 min *The lamp goes out in 6 seconds. 8 11 1 1 Cleaning with the self-cleaning recharger (continued) 1Follow the steps outlined below if the status lamp blinks or glows Cleaning the shaver without the self-cleaning during the “Clean/Dry/Charge” course or the “Clean/Dry” course. English BlinksGlowsCorrectly set the detergent cartridge and then restart a course. Remove the shaver from the self- cleaning recharger and then check that the [clean] lamp has gone out. (Be careful as the blade may be hot or wet.) Check that the water tank is correctly attached, the water tank cap is securely closed and the self- cleaning recharger is placed horizontally. IfthestatuslampgoesoutContinue a course. WhenanabnormalityhasbeencorrectedWhennoabnormalitywasfoundPress and hold [select] for approximately seconds to turn off the status lamp and then restart a course. It is time to replace the detergent cartridge and cleaning liquid inside the water tank. Drain the old cleaning liquid inside the water tank and then refill it with water. Replace the old detergent cartridge and then restart the course. WhenthestatuslampgoesoutWhenthestatuslampglowsagainContinue a course. Contact an authorized service center. recharger 1. Disconnect the power cord from the shaver. . Apply some hand soap to the outer foil. 3. Turn the shaver on and then pour some water over the outer foil. 4. Turn the shaver off after 10- 0 seconds. 5. Remove the foil frame and clean it with running water. 6. Wipe off any drops of water with a dry cloth. 7. Remove the system outer foil and the foil frame to allow them to dry completely. 1 English Replacing the system outer foil and the inner blades system outer foil once every year inner blade once every two years 1Replacing the system outer foil 1. Press the system outer foil release buttons and lift the system outer foil upwards as illustrated. . Insert the system outer foil by pushing it downwards until it clicks. 1 1. Press the foil frame release buttons and lift the foil frame upwards as illustrated. . Remove the inner blades one at a time as illustrated. • Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand. 3. Insert the inner blades one at a time until they click as illustrated. 10 Replacingtheinnerblades23 2 Cleaning the self-cleaning recharger Beard trimmings may become attached to the cleaning tray of the self-cleaning recharger. Follow the steps below to remove them. We recommend doing this each time you change the detergent cartridge. 1. Be sure to remove the water tank and the appliance plug from the self-cleaning recharger. • Be careful not to spill the cleaning liquid. . Gently wipe off any beard trimmings attached to the inside of the cleaning tray with a cloth or tissue paper dampened with water. • Clean the corners and uneven parts of the cleaning tray with a cotton swab dampened with water. • Do not pull hard on the rubber blade protector at the bottom of the cleaning tray. The rubber may come off if you pull hard on it. It is only necessary to pull it up slightly. • Warning - Do not wash or apply water to the adaptor or self- cleaning recharger. Failure to observe this may cause electric shock or result in short circuits. 11 English Removing the built-in rechargeable batteries ATTENTION: A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery. R B R C N i - M H T M Remove the built-in rechargeable batteries before disposing of the shaver. Do not dismantle or replace the batteries so that you can use the shaver again. This could cause fire or an electric shock. Replace them at an authorized service center. Disconnect the power cord from the ...