Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Do not remove the shaver from the self-cleaning recharger while using a course that includes the “Dry” function. A heater is used so the area around the blades becomes extremely hot and you may burn yourself. Place the self-cleaning recharger on a level and stable surface. Otherwise the cleaning liquid may spill and discolor leather products or other surfaces. Wipe it immediately. The self- cleaning recharger cleans the inner blades and the system outer foil. Wash with water to remove beard trimmings in other areas. English EnglishParts identification .Protective cap.On/Off switchParts identification .Protective cap.On/Off switch . System outer foil . System outer foil release buttons . Foil frame . Inner blades . Foil frame release buttons . LED display . Battery capacity monitor . high . mid . low . Charge status lamp . Trimmer . Trimmer handle . Adaptor . Power cord . Self-cleaning recharger (Referred to as the “Recharger”.) . Detergent cartridge . Water tank . Socket . Arm . Water tank cap Operating environment for the self-cleaning recharger Operating temperature: 15-35 °C (59-95 °F) Operating humidity: Less than 95% • If you use the self-cleaning recharger in temperatures outside the above range, the following problems may occur. -The time it takes to charge the shaver increases. -The recharger stops functioning. -The lifespan of the rechargeable battery shortens. (Only when you use the recharger in lower temperatures.) In this case the charge status lamp will blink twice every second. • If the charge status lamp does not glow, wait for a short while until it glows. • Depending on the environment, the shaver may not dry even if you select a course that includes the “Dry” function. In this case, wipe off any drops of water with a dry cloth. . Clean lamp . Dry lamp . Charge lamp . Status lamp . Select button . Cleaning tray . Feed water line English Charge Attach the detergent cartridge and the water tank to the self-cleaning recharger. Page 7 Insert the appliance plug. Plug in the adaptor. Pull up the arm until it clicks. Remove the protective cap and then attach the shaver. • Turn the shaver off before attaching. • Check that the outer foil is not deformed or damaged when you are attaching the shaver. Push down the arm until it clicks. • The charge status lamp glows and charging starts. • Charging is completed when the charge status lamp blinks. (Max. 1 hour later) • You can keep the shaver attached to the recharger, or connected to the adaptor, when not using it to maintain full battery capacity. You cannot overcharge the shaver. • A special plug adaptor may be required in some areas. EnglishAbout the lamp10 minutes after charging is completedBlinks red once every 2 seconds. • “high/mid/low” go out. After charging is completedBlinks red once every second. While charging Glows red. During useThe battery capacity is low when “low” blinks. • A full charge will supply enough power for approx. 14 shaves of 3 minutes each. • You can shave 1 to 2 times after “low” blinks. (This will differ depending on usage.) About the lamp10 minutes after charging is completedBlinks red once every 2 seconds. • “high/mid/low” go out. After charging is completedBlinks red once every second. While charging Glows red. During useThe battery capacity is low when “low” blinks. • A full charge will supply enough power for approx. 14 shaves of 3 minutes each. • You can shave 1 to 2 times after “low” blinks. (This will differ depending on usage.) .Charging without the self-cleaning recharger 1. Insert the appliance plug into the shaver. 2. Plug in the adaptor into a household outlet. Using the shaverShave Depress the switch lock Hold the shaver as illustrated above and button and slide shave. the On/Off switch upwards. • Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. .Using the trimmer Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns. .Preparing the self-cleaning rechargerCleaning with the self-cleaning rechargerCare English Remove the shaver and the appliance plug from the self-cleaning recharger. Remove the water tank and then open the water tank cap. Wash away the old cleaning liquid and then rinse the water tank. Pour tap water up to the feed water line. • Do not let the tap water rise above the feed water line. This may cause the cleaning liquid to spill. Securely close the water tank cap and then attach the tank. Peel off the seals from the new detergent cartridge. (2 seals) • Hold the detergent cartridge horizontally. (The detergent may spill if the detergent cartridge is tilted too much.) Attach the detergent cartridge. • Replace the detergent cartridge when the status lamp is liquid. illuminated. ...