Stimmen - 7, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This mechanism should only be activated at the end of the useful life of the shaver and should be carried out only by a Braun Service Centre. Our products are engineered to meet the highest standards of quality, functionality and design. We hope you thoroughly enjoy your new Braun appliance. Specifications Wattage 4 W Voltage range «mains operation» 100-240 V = / 50 or 60 Hz Voltage range «charging» (for cordless operation) 12-240 V = / 50 or 60 Hz The best environmental temperature range for the shaver is between + 15 °C to + 35 °C. The shaver should never be exposed to temperatures of less than 0 °C and more than + 40 °C for longer than a few hours. Keep the shaver and mains lead dry at all times. Do not handle with wet hands. Do not store in a damp environment. To avoid damage do not wind the mains lead around the appliance. It is important to check the mains lead for damage periodically particularly at each end where the mains lead enters the plug. Environmentally friendly cell unit For environmental reasons this appliance is provided with a nickel-hydrid cell unit. This cell unis does not contain any poisonous heavy metals. Nevertheless, in the interest Q-./& of recycling raw materials ^ please do not dispose of this appliance in the household waste at the end of its useful life. Disposal can take place at a Braun Service Centre or at appropriate collection sites. Description © Charging pilot light 2 Longhair trimmer switch © On/off switch 4 Switch lock «lock» © Pop-out longhair trimmer © Cutter block Shaving foil frame © Foil protection cap Cleaning brush Cordless shaving/charging When charging the shaver for the first time, connect the shaver to the mains (100 - 240 V), via the mains lead, and charge with the switch © set at «off», until the charging pilot light © goes off. The shaver should be discharged through normal shaving until it stops completely. The shaver then should be recharged from the mains (100-240 V), until the pilot light © goes off, with the switch © set at «off». This charging method preserves the life of the rechargeable cell unit. This and subsequent charges will take approximately 60 minutes (quick charge). The charging pilot light © illuminates to show that the shaver is connected to the mains. When the rechargeable cell unit is fully charged, the charging pilot light goes off. 4 The shaver automatically adapts to all international direct and alternating current voltages (12 - 240 V ¡= / 50 or 60 Hz) and all frequencies. The shaver can also be recharged on voltages below international standards in cars and boats, etc. However, a minimum 12 V outlet (direct or alternating current) is required. Recharging this way takes approximately 20 hours, and requires a special charging cord. The surrounding temperature should not be higher than + 25 °C when recharging at 12 V, to ensure the proper functioning of the shaver. A full charge will give you approximately 35 minutes of cordless shaving. Preserving the cell unit In order to preserve the life of the cell unit, it should be fully discharged approximately once every 6 months by normal shaving and then fully recharged from the mains until the charging pilot light © goes off. This procedure will condition the rechargeable cell unit, giving you the best possible shaving performance and prolonging the life of the rechargeable cell unit. The shaver should not be left in permanent charge for several weeks. Shaving with the mains lead If your shaver's rechargeable cell unit is flat (i.e. when you first use the shaver or the shaver runs out of power) you can connect the shaver directly to an outlet in order to shave immediately. If the shaver should, however, not run immediately, leave it plugged in with switch © set to «off», for approximately 1 minute. Thereafter, you can shave with the mains lead plugged into the outlet. Shaving directly via the special charging cord while connected to outlets below international standard voltages (e.g. cars, boats, etc.) is not possible. Shaving Remove the foil protection cap ® (a). Push switch © up to «on». Hold the shaver at right angles to your skin. Stretch your skin with your free hand (b). Guide the shaver smoothly against the direction of beard growth, applying only gentle pressure. Longhair trimming To use pop-out longhair trimmer ©, push switch 2 to setting «longhair trimmer». The longhair trimmer allows easy and exact trimming of the side burns (c). The longhair trimmer can be switched on and off during shaving. Switching the shaver off Push the on/off switch © back all the way to setting «off». Important: After every shave replace the foil protection cap ® on the foil frame 7. Switch lock To avoid accidentally switching on the shaver and discharging the cell unit, the switch lock should be turned on when travelling. Push switch 4 all the way down to the setting «lock». 5 Cleaning and maintenance After every shave, remove the foil frame 7 (d) and tap o...