Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Norelco Travel Adaptor Plug Kit, model TP5, may be purchased at a store near you or at a Norelco Service Store. 2A. TO CHARGE 1. Be certain your razor isOFF. ¦ First time charging requires a full 8 hours. For first time or initial charge,Green Charge Indicator Light will light to indicate razor is (re)charging. Forproper use, charge razor for the full 8 hours as directed. A fully chargedrazor will give approximately 2 weeks of 3 minute shaves per day. 2. Use only the cord provided. 3. Connect cord to razor and plug into outlet. ¦ (Re)charge at temperatures between 40°F and 95°F. Charging at lower orhigher temperatures adversely affects lifetime of batteries. ¦ (Re)charging longer thanrequired period of time will not harm razor. However, continuouslycharging razor will reduce life of batteries. 2B. TO RECHARGE ¦ After initial 8 hour charge,recharging will take only 1 hour to (re)charge batteries to full capacity. 2C. FAST 5-MINUTE QUICK CHARGE ¦ When battery is totally depleted, recharging for 5 minutes gives enoughenergy for one 3-5 minute cordless shave. ¦ If razor has not been used for at least a month, razor must be recharged for a full 8 hours (see Section 2A. TO CHARGE). 3. CORD/CORDLESS SHAVING Start with a clean, dry face. You may choose to use a pre-shave lotion to set your beard up for a close, smooth, comfortable shave, especially ifyou are using an electric razor for the first time. CAUTION: It is recommended that you wash and dry yourhands to remove any remaining lotion before handling your razor. Some lotions maycause damage to the exterior finish of your razor housing. In addition, clean razor heads more frequently to prevent pre-shave lotion build-up. A. CORD 1. Be certain razor is in OFF position. 2. Connect cord provided to razor. 3. Remove Protective Razor Head Assembly Guard. 4. Plug into 100V to 240V AC outlet. 5. Slide ON/OFF switch ON.Begin shaving. ¦ Even when cord shaving, if battery is low, wait a few seconds for razor to goON. 6. Shave against direction of beard growth using a quick, small, circular motion. 7. Keep skin taut using your fingers to stretch skin soblades can cut whiskers off. 8. Easy does it. Gently press razor to your skin sofloating heads can follow the contours of your face. 9. Turn razor OFF and unplug. ¦ It is not recommended that this razor be used exclusively as a corded razor. Continual use as a corded razor as well as continuously recharging razor will reduce life of batteries. NOTE: Razor does not recharge during shaving. B. CORDLESS 1. Charge according to directions. 2. Slide ON/OFF switch ON.Begin shaving. 4. POP-OUT SIDEBURN, BEARD AND MOUSTACHE TRIMMER 1. Push Trimmer Slide Switch up to pop out trimmer andturn razor ON. 2. Hold trimmer, as shown, to exact hairline desired. Move trimmer downward with gentle pressure (Fig. 1). 3. Turn razor OFF and brush out trimmer section using long bristles of brush. 4. Close trimmer by pushingTrimmer Slide Switch down. ¦ Lubricate trimmer teeth twice a year with Norelco Razor Lubricant, model AL80, or one drop of light machine oil. 1 5. MAINTENANCE INSTRUCTIONS IMPORTANT ¦ Always switch razor OFF and remove plug from outlet before cleaning. ¦ Always store razor withProtective Plastic Head Guard on Razor Head Assembly. ¦ Never clean, remove or replace head assembly while motor is ON. ¦ Do not apply pressure to combs. Do not touch razor heads with hard objects as this may dent n 5A. ONCE A WEEK 1. Clean Razor Head Assembly as shown (Fig. 2). 2. Press Razor Head Release Button and lift Razor Head Assembly using thumb and index finger to remove from razor housing(Fig. 3). 3. Clean inside of Razor Head Assembly and Hair Chamber with long bristles of brush (Fig. 4). 4. Press Razor Head Assembly back on razor housing. 5B. ONCE EVERY 4-8 WEEKS IMPORTANT: Do NOT interchange the cutters and combs. They are a matched set and if interchanged may adverselyaffect shaving performance until cutters reseat themselves. Therefore, remove, clean, and replace each set individually. 1. Remove Razor Head Assembly. Press Razor Head Release Button and lift Razor Head Assembly using thumb and index finger to removefrom razor housing (Fig. 5). 2. Squeeze S-formation incenter of retainer plate and lift out from Razor Head Assembly (Fig. 6). 3. Slide one cutter and comb out of frame (Fig. 7). 4. Each cutter and comb is a matched set; do not interchange them. Separateone cutter/comb, at a time, as shown (Fig. 8). 5. Cutter should be held as shown and brushed in an upward motion (Fig. 9). 6. Clean razor comb with long bristles of brush in a circular motion as shown (Fig. 10). 7. For consistently close andcomfortable shaves, razor heads should be cleaned and lubricated every 4-8weeks. After cleaning heads in a degreasing liquid (e.g. Norelco RazorCleaner, RAZORMATE Electrosonic Cleaner or alcohol), and reassembling razor, spread Norelco Razor Lubricant, model AL80, or one drop of light machine oil over floating heads with your finger. 8. Replace cutt...