Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
We hope you enjoy your new Braun Shaver. Please read the use instruction carefully and thoroughly before using the appliance. Warning Your shaving system is provided with a special cord set, which has an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise there is risk of an electric shock. This appliance is not intended for use by children or persons with reduced physical or mental capabilities, unless they are given supervision by a person responsible for their safety. In general, we recommend that you keep the appliance out of reach of children. Children should be supervised to ensure that they do not play with the appliance. Description 1 Foil & Cutter cassette 2 Long hair trimmer 3 Precision setting switch («lock») (390cc only) 4 On/off switch 5 Charging lights (green) 6 Low-charge light (red) 7 Cleaning light (yellow) 8 Replacement light for shaving parts (390cc only) 9 Shaver power socket 10 Special cord set 11 Travel pouch (390cc only) 12 Foil protection cap (350cc only) Charging The best environmental temperature for charging is between 15 °C to 35 °C. Do not expose the shaver to temperatures higher than 50 °C for extended periods of time. • Using the special cord set (10), connect the shaver to an electrical outlet with the motor switched off. • When charging for the first time, leave the shaver to charge continuously for 4 hours. Subsequent charges will take about 1 hour. • A full charge provides up to 45 minutes of cordless shaving time depending on your beard growth. • Shave without the cord. With normal use the shaver will be charged automatically after every cleaning in the Clean&Renew™ (see «C Clean&Renew™»). • Maximum battery capacity will only be reached after several charging/discharging cycles. • 5-minute quick charge (with the special cord set (10)) is sufficient for a shave. • If the rechargeable batteries are discharged, you may also shave by connecting the shaver to an electrical outlet via the special cord set. Charging lights (5) The green charging lights show the charge status of the batteries. The green charging light blinks when the shaver is being charged or switched on. When the battery is fully charged, all green charging lights shine permanently, provided the shaver is switched on or connected to an electrical outlet. Low-charge light (6) The red low-charge light flashes when the battery is running low. You should be able to finish your shave. A Shaving Press the on/off switch (4) to operate the shaver (picture). The flexible shaving foils automatically adjust to every contour of your face (picture). Long hair trimmer (2) To trim sideburns, moustache or beard, slide the long hair trimmer upwards. Precision setting switch («lock») (3) (390cc only) For precise handling in hard to shave areas (e.g. under the nose) slide the switch (3) to the right to position «lock». The centre trimmer and one foil will be lowered. Tips for the perfect shave For best results, Braun recommends you follow 3 simple steps: 1. Always shave before washing your face. 2. At all times, hold the shaver at right angles (90°) to your skin. 3. Stretch your skin and shave against the direction of your beard growth. B Keeping your shaver in top shape Cleaning indicator Your shaver should be cleaned daily in the Clean&Renew™, and certainly when the yellow cleaning light (7) shines constantly after shaving. If this is not done, the yellow light will go out after some time. The shaver’s electronics will then assume it has been cleaned manually and a new calculation of the time when the next cleaning is required will be started. During the cleaning process in the Clean&Renew™ the yellow light will flash and will go off after approx. 4 hours when cleaning is finished. Automatic cleaning Once the shaver is put into the Clean&Renew™, it is cleaned automatically (see «C Clean&Renew™»). Manual cleaning is recommended only when the Clean&Renew™ is not available, e. g. when travelling. Manual cleaning The shaver head is suitable for cleaning under running tap water. Warning: Detach the shaver from the power supply before cleaning the shaver head in water. Regular cleaning ensures better shaving performance. Rinsing the shaver head under running water after each shave is an easy and fast way to keep it clean: • Switch the shaver on (cordless) and rinse the shaver head under hot running water. You may use liquid soap without abrasive substances. Rinse off all foam and let the shaver run for a few more seconds. • Next, switch off the shaver, remove the shaver Foil & Cutter cassette (1) and let it dry. • If you regularly clean the shaver under water, then once a week apply a drop of light machine oil onto the long hair trimmer (2) and shaver Foil & Cutter cassette (1). Alternatively, you may clean the shaver using a brush: • Switch off the shaver. Remove the shaver Foil & Cutter cassette and tap it out on a flat surface. • Using a brush, clean the inner area of the shav...
Dieses Handbuch ist für folgende Modelle:Rasierer - BRAUN 390CC (6.42 mb)