Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
2 Installation .......................................................................................................................... 4 Final Steps........................................................................................................................... 5 Please read all instructions before using this appliance. WARNING If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. PARTS NEEDED: • Tape Measure • Straight Edge or Ruler • Phillips Head Screwdriver • Level • Pencil • Wire Cutters or Wire Stripper • Wire Nuts • Volt Meter (0-250 VAC) • 1” Hole Saw • Hand or Saber Saw • Drill and Drill Bit • Safety Gloves and Goggles • Cloth or cardboard (Optional - to Protect Floor) WARNING Before installing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally. CAUTION Do not use the oven for storage. Unit is heavy and requires at least two people or proper equipment to move. Important: Save these instructions for the local inspector’s use. Installer: Please leave the instructions with the unit for the owner Owner: Please save these instructions for future reference. • Remove all tape and packaging before using the oven. Destroy the packaging after unpacking the oven. Never allow children to play with packaging material. • Be sure your appliance is properly installed and grounded by a qualified technician in accordance with the National Electrical Code ANSI/ NFPA No. 7 latest edition (or the Canadian Electric Code) and local electrical code requirements. Important: Local codes vary. Installation, electrical connections and grounding must comply with all applicable codes. • Install only per installation instructions provided in the literature package for this oven. • Ask your dealer to recommend a qualified technician and an authorized repair service. • Know how to disconnect the power to the oven at the circuit breaker or fuse box in case of an emergency. • Do not repair or replace any part of the appliance unless specifically recommended in the manuals. All other servicing should be done by a qualified technician. This may reduce the risk of personal injury and damage to the oven. • Never modify or alter the construction of an oven by removing panels, wire covers, screws, or any other part of the product. • DO NOT LIFT OVEN BY DOOR HANDLE. Remove the door for easier handling and installa- tion. See ‘Removing the Oven Door’ in the Mainte- nance section of the Use and Care Manual. Safety Preparation Installation Final Steps English • 1 Steps 1 through 3: Preparation Safety InstructionsPreparationInstallationFinal Steps 1. Prepare Cabinets General Instructions: • The single oven can be installed under a counter or in a wall or cabinet. The double oven can be installed in a wall or cabinet. • Choose a location away from strong drafts and where electrical power can be provided. • The oven support surface must be a minimum 3/4” thick plywood platform. For single ovens, it must support 150 pounds. For double ovens, it must support 290 pounds. The platform must be solid, level and flush with the bottom of the cabinet cut out. Cabinet Cutout Dimensions See Table 1, below and Figures 1, 2 and 3 on following page for cutout dimensions. 2. Prepare Electrical Outlet Warning: Turn power off at service panel and lock service panel before beginning. General Information Ovens are dual rated for use on either 120/240 VAC or 120/208 VAC. See Table 2 at right for power ratings and circuit breaker sizes based upon the supply voltage for each model. The junction box must be located in the indicated space in Figures 1,2 and 3, next page. It should be easily reached through the front of the cabinet where the oven will be located. Verify that wiring to house is adequate. Contact your local utility company to verify that the present electric service to your home is adequate. In some instances, the size of the wiring to the house and service switch must be increased to handle the electrical load demanded by the oven. Verify that wiring inside house is adequate. Most wiring codes require a separate circuit with separate disconnect switch and fuses either in the main entrance panel or in a separate switch and fuse box. Most local building regulations and codes require that electrical wiring be done by licensed electricians. Be sure to install your oven according to the electric codes in place in your region. 3. Prepare Oven Remove any remaining packaging and discard. Remove racks, accessories and oven door(s) and set aside. See instructions in Use and Care Manual for proper removal of oven doors. DO NOT lift oven by door handles! Place oven in front of cabinets where it is to be installed. Rest it on a jack or other sturdy support so that it is in line with the cabinet cutout. Table 2: Electrical Specifications Electrical Specifications Model HBL503, HBL504 Volts 120/240 Watts 3,350 Amps...