Stimmen - 5, Durchschnittliche Bewertung: 3.6
(
)
)
|
Anleitung Zusammenfassung
Cylinder Specification Any LP gas supply cylinder used with this pizza oven must be constructed and marked in accordance with either: Specifications for LP-Gas Cylinders• of the U.S. Department of Transportation, or National Standard of Canada, • CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission. The LP cylinder must be approximately 12 inches in diameter and 18 inches high. The maximum fuel capacity is 20 lbs. of propane, or 5 gallons. Full cylinder weight should be approximately 38 lbs. (43.7 lbs. nominal water capacity.) Never fill the cylinder beyond 80% full. LP Gas Hook Up Vent the enclosure for an LP gas cylindar with openings at the level of the cylinder valve and at the floor level. Ensure one side of the enclosure is completely open. For enclosures that have four sides, complete with a top and bottom: At least two ventilation openings at cylinder valve less than • one square inch per pound (7.1 cm./kg) of stored fuel capacity and not less than a total free area of 10 square inches (64.5cm.). If ventilation openings at floor level are in a sidewall, there shall be at least two openings. The bottom of the openings shall be at floor level and the upper edge no more than 5 inches (127 mm) above the floor. The openings shall be equally sized, spaced at 180. (3.14 rad) and unobstructed. Every opening shall have minimum dimensions so as to permit the • entrance of a 1/8 inch (3.2 mm) diameter rod. Transporting and Storing LP Gas Place the dust cap on the cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane. Transport only one cylinder at a time. Ensure the cylinder is secured in an upright position with the control valve turned off and the dust cap in place. Store cylinders outdoors and out of reach of children. Do not store cylinders in a building, garage, or any other enclosed area. Natural Gas Warning: All pizza ovens use LP unless they are converted to natural gas. Do not connect natural gas to an unconverted pizza oven! Requirements Always check the rating plate to make sure the gas supply you are hooking up to is the gas type the pizza oven is manufactured for. IMPORTANT: Never connect the pizza oven to an unregulated gas supply. The installation of this appliance must conform with local codes or, in the absence of local codes, to the national fuel gas code, ANSI Z223.1a-1998. Installation in Canada must be in accordance with the standard CAN/CGA-B149.2, Propane Installation Code. A licensed contractor or local gas company representative must perform all natural gas connections. Ensure that the service supplying the pizza oven is fitted with a shut off valve conveniently positioned near the pizza oven and giving ease of access. The pizza oven and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressure in excess of 0.5 psi (3.5 kPa). Your pizza oven for use with natural gas comes equipped with its own regulator that MUST NOT be removed. If this regulator needs to be replaced, use only the type specified by Cal Flame™ for this appliance. Connection Remove the rear panel from the pizza oven to gain access to the 1. regulator and gas connection point. Connect a suitable flex connector to the regulator.2. Check the controls to ensure all control valves are in the full OFF 3. position. Turn on the main gas supply and check all connections for leaks 4. using soapy water as described in the leak testing procedure section. Warning: If you see bubbles in the soapy solution at any of the connections, turn off the gas supply and tighten the connection. If tightening the connection does not seal the leak, it may be necessary to replace the flex hose. Installing the Transformer All grills with electrical components such as lights or a convection fan will require the transformer to be installed and plugged in before you can use it. This needs to be done before the grill is inserted in the island or modular cart. When the transformer is attached to the grill chassis, use care in placing the grill in the island cutout to avoid hitting the transformer. Remove the transformer 1. and the metal screws from the plastic bag. Place the grill on a sturdy 2. surface and tilt it back to show the underside of the grill. Using the metal screws, 3. attach the transformer to the left side of the grill near the internal electrical connection. Attach the metal plate to the outside surface of the grill as shown in the figure below. When you have firmly 4. tightened the screws and nuts, connect the plug from the transformer to the grill. Screw on the stainless steel retainer. Installing the Bricks and Rack The pizza oven uses three white bricks for diffusing heat from the burners. After you have removed the pizza oven from the box...