Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Press the UP or DOWN button as needed to display the required setting. • The hold mode may be disabled on any program individually. The timed cook cycle may also be disabled, and the controller will operate as a holding timer. This is done by setting the cook or hold time to “OFF”. • The controller may also operate with the cook and/or hold temperature set to “OFF”. When both the cook and hold temperature are set to “OFF”, the controller will not regulate the oven temperature. This feature is intended for demonstration or display purposes. Reviewing a Program 1. Press the REVIEW button. The display will be blank and a program LED will be flashing. 2. Press the ITEM SELECT button to display the flashing LED for the desired program. 3. Press and hold the desired function button. The current setting will be displayed. 4. To change the setting, press the UP or DOWN button while holding the function button. • If a button is not pressed within five (5) seconds, the controller will exit review mode and continue the cycle previously in progress. • The cycle in progress will continue to count up or down accordingly while in the review mode. • If a cycle is changed during a timed cook and/or hold cycle and the time is set for a value that is less than the elapsed time for the current cycle, the current cycle will be completed when the review mode is exited. • If the cycle in progress goes into audible alert while in review mode, the controller will exit review mode and all changes will be canceled. Cooking 1. Place the POWER switch, OVEN LIGHTS switch, and ROTOR CONTROL switch located on the front panel in the “ON” position. The controller will automatically load the settings from the last program selected and begin regulating to the cook or hold temperature. Typically, the oven temperature is too cool upon power-up. If the oven temperature is below the programmed temperature, the display will alternately flash “too”, “CooL” until the oven temperature reaches the programmed temperature. 9 Countertop Rotisserie Oven Operation 2. Select the desired program by pressing the ITEM SELECT button until the LED corresponding to the desired program is illuminated. 3. When the controller reaches the programmed temperature, the display will alternate between “rEdy” and the current oven temperature. The audible alert will also sound for five (5) seconds. The audible alert may be canceled early by pressing the START/STOP button. The display will continue to flash the ready message. During the ready message, the operator may also change to a new program. Since each program may be set for a different temperature, the controller may require a warm-up or cool-down period for the oven to get in range. If the oven temperature is out of range from the new setting, the display will show either “too Hot-OPEn door” or “too CooL”, until the oven temperature comes within range of the new setting. The ready message will again be displayed. Once the display shows “rEdy”, if the oven temperature falls out of range again (due to the door opening to load product), the “too Hot” or “too CooL” message will not be displayed. The “too Hot” or “too CooL” messages are disabled during a cycle. 4. Open the oven door and load the product. Use the ROTOR CONTROL switch on the front panel to operate the rotor during loading. 5. Once the product is loaded, close the door. 6. When the display is flashing the ready message and you want to start the cook cycle, press the START/STOP button. 7. When a cook cycle ends, do one of the following: • If a hold time/temperature has not been programmed, an alarm will sound and the display will flash the message “donE” until a button is pressed. Press the START/STOP button to enter the stop mode. • If a hold time/temperature has been programmed, the hold cycle will start. During the hold cycle the oven temperature will be regulated to the programmed hold temperature setting. When the accumulated hold time reaches the hold time setting, an alarm sounds and the display will flash the message “HoLd donE” until a button is pressed. Press the START/STOP button to enter the stop mode. Power Failure During Cooking Cycle The controller will suspend operation retaining programs and cycle times. When power is restored, operation will resume where left off when power failed. Probe (Thermocouple) Diagnostics If the probe (thermocouple inside the oven) stops working, the controller will cancel the cooking cycle, an audible alert will sound, and the display will show “PROB”. 10 Countertop Rotisserie Oven Installation Installation Serious injury, equipment damage or death could result if attempting to install this oven yourself. Ensure that an authorized BKI service agent installs the oven. Unpacking and Handling It is the owners’ responsibility to file all freight claims with the delivering truck line. Inspect all cartons and crates for damage as soon as they arrive. If damage to cartons or crates is found, or if a shortage is found, not...