Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Wolf Dateigröße: 108.98 kb Dateiname: Unterrichtssprache:

Attach the four leg assemblies with the 24 bolts and lockwashers (6 per leg). Place the lower oven (with legs) on the floor and remove two 7.16" (11 mm) diameter knockouts on each side of the top cover. Install two locating studs to the bottom of the top oven per stacking kit instructions. Move the oven with legs to the installed position. Place the upper oven on top of the lower oven using the locating studs. Remove the optional rear panel, if provided, from the TOP oven. Install the Stacking Flue (Fig. 3) with the four screws provided. Replace the top oven rear panel, if provided. STACKING FLUE PL-53463 Fig. 3 – 5 – ELECTRICAL CONNECTIONS (Stacked Ovens) WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT. Make sure that the electrical power supply agrees with the specifications on the oven data plate, the wiring diagram on the oven, and with Electrical Data, page 5. 1. Wires to connect both ovens are provided with each oven. Carefully route these leads from the top oven through the bushing (supplied with the stacking kit) through the electrical access knockout holes common to both ovens. 2. Connect wires X, Y, and Z from the upper oven to the lower oven per the wiring diagram using wire nuts provided. Attach the power supply conduit to the bottom of the lower oven. Connect the power supply leads to the line side of the terminal block on the bottom oven. 3. Finally, inspect and check all wiring and terminal connections for tightness and proper routing away from any moving parts (relay solenoid core), or pinch points (cover on oven frame). 4. Refer to reference drawing 426986 supplied with the stacking kit for electrical connection instructions. 5. Refer to instructions supplied with the stacking kit for marking the combined electrical load information to the electrical data plate of the bottom oven. BEFORE FIRST USE (All Models) Before using the oven for the first time, it must be burned off to release any odors that might result from heating the new surfaces in the chamber. 1. Using a clean damp cloth, wipe the inside of the oven, including the racks. 2. Close the oven doors, turn the Master Switch ON, turn the Thermostat to 300°F (149°C) and allow the oven to cycle for 6 to 8 hours before turning the Master Switch OFF. – 6 – OPERATION WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING, OR PERFORMING ANY MAINTENANCE. CONTROLS — MODELS WKE / WKEX / WKED / WKEDX MOVE TO VENT MASTER SWITCH ON HEAT OFF TEMPERATURE TIMER LOW HI FAN SPEED OVEN COOL OFF OFF ON LIGHTS 0 5 10 15 20 25 30 35 40 45 50 55 60 150 250 200 300350200 400 450 250 500 F 100 C Models WKE / WKEX MOISTURE VENT DAMPER MASTER SWITCH ON LIGHT (Amber) HEAT LIGHT (White) TEMPERATURE TIMER FAN SPEED LIGHTS Models WKED / WKEDX PL-53495 MOVE TO VENT MASTER SWITCH ON HEAT OFF TEMPERATURE TIMER LOW HI FAN SPEED OVEN COOL OFF ON LIGHTS 0 5 10 15 20 25 30 35 40 45 50 55 60 150 150 225 250 275 300 325 350 375 200 425 475 F 400 450 250 500 100 C PL-53494 – Open the damper to exhaust excess moisture. Close the damper when cooking dry products. Select settings between OPEN and CLOSED for optimum performance. – ON -Turns oven control circuits on. – OFF - Turns oven control circuits off. – OVEN COOL - Allows the fan motor to run with the doors ajar to speed oven cooling. – Lit when MASTER SWITCH is turned to ON. – Comes on and goes off when the heating elements cycle on and off. – Controls oven temperature. – Use to set the cooking time. Alarm sounds continuously when time has elapsed to 0. Turn the timer OFF to silence the alarm. The timer does not turn the oven off. Keep timer set to OFF when the oven is not in use. – Adjust air velocity in the oven cavity. HI - Normal operating speed. LOW - Use this setting when cooking a delicate product like meringue, which could blow around in the oven. – ON - turns the interior lights on. – OFF - turns the interior lights off. – 7 – USING MODELS WKE / WKEX / WKED / WKEDX Preheating 1. Turn Master Switch ON. Amber ON light will come on, indicating that power to oven is on. 2. Set Thermostat as desired. Refer to COOKING GUIDELINES for suggested temperatures and times for various products. 3. Prepare product and place in suitable pans. When white HEAT light goes off, oven has reached desired preheat temperature. Cooking 1. Open doors and load the product into the oven. Place pans in the center of the racks. Close doors. 2. Set the Timer. After the preset time lapses, turn timer to OFF position to stop alarm. 3. When product is done, open doors and carefully remove cooked product from the oven. Wipe up any spills. End of Day 1. Turn thermostat to OFF. 2. Turn Master Switch to OVEN COOL. Leave doors open while the fan is on to cool the oven. 3. When oven has cooled su...

Herunterladen

Geben Sie zwei Ziffern: