Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Thermador Dateigröße: 2.26 mb Dateiname: Unterrichtssprache:

• Failure to grasp the oven door firmly and properly could result in personal injury and product damage. • With the door off, never release the levers and try to close the hinges. Without the weight of the door, the powerful springs will snap the hinges closed with great force. To Remove the Oven Door: 1. Fully open the oven door. 2. Raise the U-clip over the hook on each of the hinges to the "locked" position (see illustration below). This will prevent the hinge from snapping closed when the door is removed. 3. Grasp the door by the sides toward the back. Raise the front of the door several inches (there will be some spring resistance to overcome because of the hinge being locked). When the front of the door is high enough, you will be able to lift the hinges to clear the indents. 4. Pull the hinges out of the slots in the oven front frame. To Replace the Oven Door: 1. Grasp the sides of the door at the center and insert the ends of the hinges into the slots in the oven front frame as far as they will go (see illustration below). 2. With the door open all the way, lower the two locking clips. 3. Raise the oven door and make sure that it fits evenly with the front sides. 4. Close and open door slowly to be sure it is correctly and securely in place. 5. Door must be straight, not out of alignment. HINGE CLIP Door Hinge Close-up View HINGE ARM 32 Do-It-Yourself Maintenance SEM/SEMW Oven Care and Use Manual Do-It-Yourself Maintenance Replacing the Oven Light CAUTIONS: To prevent personal injury: • Before replacing the light bulb, be sure the electric power is turned off at the circuit breaker. • Halogen bulbs get HOT instantly when turned ON. • Be sure the oven and light bulb are cool. • Do not operate the oven unless the light cover is securely in position. CAUTION: If the light cover is damaged or broken, do not use the oven until a new cover is in place. The oven lights are located on the top ceiling wall of the oven. The lights have a removable lens cover and a halogen light bulb. The ceramic light socket housing is not removable by the user. Replace bulb with a 12-Volt, 10-Watt Halogen bulb only. To replace Halogen Bulb: 1. Turn off circuit breaker. 2. Remove oven racks. 3. Slide the tip of a table knife blade between the fixing clip and the glass lens cover. 4. Support the glass lens cover with two fingers along the bottom edge to prevent the cover from falling to the bottom of the oven. 5 Gently twist the knife blade to loosen the glass lens cover. 6. Remove the glass lens cover and fixing clip. 7 Remove the bulb by grasping and sliding the bulb straight up until the two prongs have cleared the ceramic holder. 8. Do not touch the glass of the new replacement bulb with your fingers. It will cause the bulb to fail when it first lights. Grasp the replacement bulb with a clean paper towel or facial tissue with the prongs facing down. Locate the two prongs in the ceramic holder, gently poking until the two prongs locate in the ceramic socket. 9. Press down to seat the bulb. 10W HALOGEN LAMP Lens Fixing Clip Holder Clip Housing Ceramic Holder 10. Place the fixing clip on the lens cover. 11. Slide the protective lens into the holder clip and push the other end until the fixing clip snaps back into the housing. 12. Turn on circuit breaker. Changing to the 24-Hour Clock Format The oven has been preset to a 12- hour clock format. To change the Time-of-Day Clock to a 24-Hour Clock, follow these steps: 1. Turn off both ovens. 2. Touch START and hold the CLOCK pad at the same time. 3. 12H appears in the Clock window; release both pads. 4. Touch CLOCK and 24H replaces 12H. This alternates when CLOCK is touched. 5. To complete the change, touch START. 33 Do-It-Yourself Maintenance Do-It-Yourself Maintenance Do-It-Yourself Maintenance Fahrenheit to Celsius The oven has been preset to a Fahrenheit temperature. To change to Celsius, follow these steps: I. Turn off ovens. 2. Touch and hold the START pad and then the CONVECTION pad at the same time for 3 seconds. 3. “F” appears in the temperature digits; release both pads. 4. Touch CONVECTION; “C” replaces “F.” This alternates when CONVECTION is touched. 5. To complete the change, touch START. Voltage Change Option The oven has been preset for 240 VAC. If your residence has been supplied with 208 VAC, the oven voltage can be changed during installation. 1. Turn both ovens off. Touch OVEN OFF for each oven. 2. Touch and hold the START pad and the SELF CLEAN pad at the same time for 3 seconds. 3. “240” appears in the display. Release both pads. 4. Touch the SELF CLEAN pad. “240” is replaced with “208.” This alternates when SELF CLEAN is touched. 5. To complete the change, touch START. Calibrating Oven Temperature The electronic thermostat has been preset to 0°F and accurately maintains its setting. If the browning results are too light or too dark for your preferences, you can raise or lower the setting. To change calibration of oven temperature for single or upper ovens: 1....

Herunterladen

Geben Sie zwei Ziffern: