Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung AEG, modell COMPETENCE B4101-4

Hersteller: AEG
Dateigröße: 676.74 kb
Dateiname: 926487en.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Hanging the oven door 1.From the side of the door on which the handle is positioned, take hold of the sides of the door with both hands. 2.Hold the door at an angle of approx. 60°. 3.Insert the door hinges as far as possible into the two slots on the right and left at the bottom of the oven at the same time. 4.Lift the door up until resistance is met and then open it fully. 5.Fold the clamping levers on both door hinges back into their original position. 6.Close the oven door Oven Door Glass The oven door is fitted with three glass panels mounted one behind the other. The inner panels may be removed for cleaning. 1 Warning: Carry out the following steps only when the oven door is unhinged! When left on its hinges, the door could rise rapidly due to the lighter weight when the glass is removed and could cause injury. 1 Important: Using force, especially on the edges of the front glass panel, may break the glass. Removing the top door glass 1.Unhinge the oven door and place it on a soft, flat surface with the handle facing down. 2.Take hold of the upper glass panel at the lower edge and slide it against the spring pressure in the direction of the oven door handle until it is free at the base (a). 3.Raise the panel gently at the base and pull out (a). Removing the middle door glass 1.Grip the bottom edge of the middle glass panel and push it in the direction of the oven door handle until it is free at the base (a). 2.Raise the panel gently at the base and pull out (a). Clean the glass door panels Inserting the middle door glass 1.Insert the middle glass panel at an angle from above into the section of the door in which the handle is located (a). 2.Lower the middle glass panel and slide it under the lower bracket towards the lower door edge as far as it will go (a). Inserting the upper door glass 1.Insert the upper glass panel at an angle from above into the section of the door in which the handle is located (a). 2.Lower the glass panel. Lay the panel against the spring on the lower door edge in front of the retaining section on the handle side, and slide it under the retaining section (a). The glass panel must be firmly in position! Re-hang the oven door What to do if … Problem Possible cause Remedy The oven does not heat up The oven is not switched Switch the oven on on The clock is not set Set the current time on the clock The required settings have Check the settings not been set The house wiring fuse (in Check the fuse the fuse box) has tripped If the fuses trip several times, please call a qualified electrician The oven lighting is not The oven light bulb is Replace the oven bulb operating faulty If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. 1 Warning! Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs. 3 If the appliance has been wrongly operated, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period. 3 Advice on cookers with metal fronts: Because of the cold surface at the front of the cooker, opening the oven door during (or just after) baking or roasting may cause the glass to steam up. Installation Instructions 1 Attention: The new appliance may only be installed and connected by a registered expert. Please comply with this. If you do not, any damage resulting is not covered by the warranty. 1 Safety information for the installer • The electrical installation is to be set up so that the appliance can be isolated from the mains with a minimum 3mm all-pole contact separation. Suitable separation devices include e.g. cut-outs, fuses (screw fuses are to be taken out of the holder), RCD’s and contactors. • Anti-shock protection must be provided by the installation. • The built-in unit must meet the stability requirements of DIN 68930. • Built-in ovens and built-in cooking surfaces are fitted with special connection systems. For safety reasons, they must only be combined with appliances from the same manufacturer. Guarantee Conditions Weitere Kundendienststellen im Ausland In diesen Landern gelten die Garantiebedingungen der ortlichen Partner. Diese konnen dort eingesehen werden. Further after-sales service agencies overseas In these countries our AEG agents’ own guarantee conditions are applicable. Please obtain further details direct. Autres agences etrangeres assurant le service apres-vente Dans ces pays, les conditions de garantie des concessionnaires de la region sont valables. Vous pouvez les consulter sur place. Otros puntos de Postventa en el extranjero En estos paises rigen las condiciones de nuestros representantes locales. las cuales pueden ser consultadas alli mismo. Ulteriori uffici del servizio tecnico assistenza clienti all’estero In questi paesi sono valide le condizioni di garanzia dei partner locali. Queste condizioni possono essere es...