Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The bell can bastopped manually by turning the shaft © to put the hand © on the position STOP . 16 Cooking Time : Shaft ® Disk (§) »*■ Immediate start of cooking and automatic stop of cooking. >- Maximum duration: 180 minutes (3 hours). >- To set the cooking time, turn the shaft (D clockwise and put the graduation of the disk © in front of the ® index (D of the dial. >- The end of cooking is indicated by a bell which stops automatically after 3 minutes. The disk © indicates “0” (off position). This bell can be stopped manually by turning the shaft (§) in order to put the “0” of the disk in front of the index Cooking Start Time : Shaft © Hand© ■* Cooking completely automatic with delayed start and automatic stop of cooking. Maximum delayed start: 12 hours. Before setting the cooking start time, ensure that the “0” of the disk 0 is positioned in front of the index(E) of the dial. To set the cooking start time, pull and turn the shaft ©in both directions (clockwise and anticlockwise) and put the hand (f) in front of the cooking start time. When this operation is over set the cooking time as above mentioned. Future transportation * Transporting the oven; Store the oven's original box. Transport the oven in its original carton. Follow the guidance marks that are printed on the carton. To prevent the wire grill and tray inside the oven from damaging the oven door, place a strip of cardboard or paper 1 to 1.5 cm in thickness onto the inside of the oven door that lines up with the position of the trays. Tape the oven door to the side walls. * If you do not have the original carton; Take the necessary precautions in order to prevent the exterior panels, and the glass surfaces of the oven from being damaged. Pack the oven in bubble wrap or thick cardboard and tape it securely in order to prevent damage during transportation. The oven must be transported upright. Do not place other items on the top of the cooker. 17 n Maintenance and cleaning Turn off the mains switch before cleaning. * Before switching on again ensure that all controls are in the OFF position. * Never dean the cooker surface by using materials such as hurd brushes, steel pads or knives, which can easily scratch the enamelled and stainless steel surfaces. Control panel Wipe over the control panel with a damp doth and polish with a dry cloth. Do not use oven cleaners or aerosols, scouring pads or abrasive powder for cleaning the plastic knobs as damage will occur, Do not attempt to remove any of the control knobs from the panel as this may cause damage and is a safety hazard. * Special cleaners that are commercially avaible may be used after carefully reading the warning labels written on them. Do not use cleaning agents containing acid or chlorine. Cleaning can be accomplished using a soft piece of cloth wetted with soapy water or with commercially avaible special surface cleaners and a soft piece of cloth. Especially use liquid paste or cream type cleaners. Warning! Never clean the inside of the oven and trays with hard brushes, steel pads or knives. Do not use cleaning agents containing acid or chlorine on stainless steel surfaces and the handle. Cleaning can be accomplished using a soft piece of cloth wetted with soapy water or with commercially available special surface cleaners and a soft piece of doth. 18 /-\ Oven interior Before switching on again ensure that all controls are in the OFF position. Take out all trays and Ihe grill out of the oven. Clean out the interior with a piece of moist, soapy cloth. Then, clean it once more with a wet piece of cloth and let it to dry. Do not use dry powder agents far cleaning. Special cleaners that are commercially available may be used after carefully reading the warning that are written on the labels. * Catalytic-enamelled models; The oven interior of this model is coated with catalytic enamel since the catalytic enamel cleans itsellf, you do not have to perform an extra cleaning after ^ the cooking operation. If your oven obtains steel rack; To clean the steel rack, unscrew the 4 screws. After cleaning operation, assemble the steel rack to the oven body again. Steel wool I Cleaning powders Hard abrasive sponges Do not use these materials for cleaning Lowering the heating element Warning! Make sure that the heating element is sufficiently cool before you start cleaning. Warning! Never switch on the heating element or place any wright on it when the heating element is in the lowered position. 1. Unlock the heating elementby turning the screw at the seiling of the oven cavity. 2. After cleaning, move the heating element upward and screw it to the ceiling of the oven cavity. Replacing the oven lamp: 1. Unplug the power cable. 2. Then, remove theprotective glass cover of the lamp inside your oven by turning it counterclockwise. 3. Then, remove the bulb by turning it counter-clockwise. 4. After installing the correct bulb obtained from an Authorized Ser...