Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Bottle of Engine Oil One Operator's Manual 20-oz. Bottle of EngineOil Tamper Figure 1 Lowering the Chipper Chute shredder without chipper chute lowered into the operating position. WARNING: Never operate the chipper For shipping reasons, the unit is cartoned with its chipper chute in a raised position.To pivot it downward, into the operating position, proceed as follows: Pull the spring latch upward and gently pivot the chipper chute down until it clicks into the lock rod. See Figure 2. Figure 2 Raising the Chipper Chute shredder without chipper chute lowered into WARNING: Never operate the chipper the operating position. For convenience when storing, the chipper chute can be pivoted upward. To do so, proceed as follows: Pull the lock rod outward and pivot the chipper chute upward until it clicks into the spring latch. See Figure 3. Latch Lock Rod" Figure 3 Attaching The Debris Collection Bag To attach the bag, place the opening of the bag completely over the discharge chute. Position the bag so that the wing knobs which secure the discharge chute to the housing are completely covered. Pull on the drawstrap until the bag is tight around discharge chute. See Figure 4. 4ousing Debris Collection Bag Figure 4 Emptying the Debris Collection Bag Squeeze the locking buckle to release the bag's drawstrap before loosening it from the discharge chute. See Figure 5 Empty the bag and reattach to the discharge chute opening. Refer to Figure 4. Locking Buckle J Figure 5 Know Your Chipper Shredder Read this operator's manual and safety rules before operating your Chipper Shredder. Compare the illustrations below with your equipment to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. The operation of any Chipper Shredder can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses, provided with the Chipper Shredder, while operating this equipment or while performing any adjustments or repairs on it. Hopper Handle Spark Plug Wire Air Cleaner Chok_ Control Throffie Tamper Lever Spring Latch Starter Handle Discharge Chute Oil Fill / Muffler Oil Drain Chipper Chute Reduction Chamber Engine j, Lock Rod Figure 6 Operating Controls (See Figure 6) WARNING: Never operate the chipper shredder with the chipper chute in the raised Spring Latch position. Release the spring latch to lower the The spring latch is located onthe top of the hopper. It is chipper chute into the operating position used to secure the chipper chute in a raised position for before starting the engine. storage or for transporting. Lock Rod Handle The lock rod is located on the chipper chute support. It Use the handle when transporting the chipper is used to release or lock the chipper chute in a lowered shredder. position for operation. Chipper Chute Branches up to 3" in diameter may be fed into the chipper chute for chipping. Meets ANSI safety standards Craftsman Chipper Shredders conform to the safety standard of the American National Standards Institute (ANSi). 8 Use the tamper to assist in feeding branches into the Tamper chipper chute. Hopper Leaves, twigs and branches up to 1/2-inch in diameter may be placed into the hopper for shredding. IMPORTANT: Never place branches with a diameter greater than 1/2-inch in the hopper. Doing so can result in serious damage to your unit's shredder blade, flails or impeller. Engine NOTE: In the state of California, the 110000 series engines covered in this manual are certified by the California Air Resources Board to meet emissions standards for 250 hours. Such certification does not grant the purchaser, owner or operator of this engine any additional warranties with respect to the performance or operational life of this engine. This engine is warranted solely according to the product and emissions warranties stated elsewhere in this manual. Bore 2-11/16 in. (68 mm) Stroke 2-13/64 in. (56 mm) Displacement 12.48cu. in.(206cc) IMPORTANT:For practical operation, the horsepower loading should not exceed 85% of rated horsepower. Engine power will decrease 3-1/2% for each 1,000 feet (300 meters) above sea level and 1% for each 10° F (5.6° C)above 77°F(25°C).Engine willoperate satisfactorily at an angle up to 15 degrees. Throttle Lever The throttle lever controls the engine speed and stop function. Choke Control The choke control closes the choke plate on the carburetor and aids in starting a cold engine. Starter Handle The starter handle is located on the engine. Pull the starter handle to start engine. Stopping Engine Move throttle control lever to STOP position. See Figure 7. Figure 7 WARNING: When moving throttle control ,_ lever, be careful of heated surfaces on muffler guard. A CAUTION: Never stop the engine by ,_. moving the choke lever into the CHOKE position. Backfire, fire or engine damage could result. Gas And Oil Fill-up Oil (one 20-oz. bottle included) IMPORTANT:The chipper shredder is shi...