Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: MTD Dateigröße: 1.18 mb Dateiname: Unterrichtssprache:

Depress the plunger on the drawstring, pull on the drawstring until the bag is tight around the chute opening. Release plunger to lock it into position. -See figure 2. 3 OPERATION KNOW YOUR SHREDDER READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SHREDDER. Compare the illustrations with your shredder to familia ize yourself with the location of various controls and adjustments. Save this manual for future reference. OPERATING CONTROLS CHOKE LEVER—Used to enrich the fuel mixture in the carburetor when starting a cold engine. STARTER HANDLE—Used to manually s art the engine. THROTTLE CONTROL—Controls engine spe ed and stops the engine. The operation of any shredder can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields. We recommenc wide vision safety mask for over: spectacles or standard safety glas! ;es. BEFORE STARTING 1. Place the shredder on a firm, level surface 2. Service engine with gasoline and oil as ins tructed in the separate engine manual packed w:th your shredder. 3. Attach spark plug wire to spark plug. NOTE: Check the fuel level periodically to avoid running out of gasoline while operating the shredder. If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit before it can be restarted. Refer to “Removing the Flail Screen” on page 6. TO START ENGINE A WARNING: Be sure no one other than the operator is standing near the shredder while starting or operating. 1. Place the throttle control lever in FAST position. Refer to separate engine manual. 2. Move choke lever to CHOKE position (a warm engine may not require choking). 3. Grasp starter handle and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly. 4. Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope N rewind slowly. Do not let starter handle snap back against starter. 5. Repeat preceding instructions 3 and 4 until engine fires. When engine starts, move choke lever on engine halfway between CHOKE and OFF. 6. Move throttle control to SLOW position for a few minutes warm-up. Move choke lever to OFF position as engine warms up. NOTE: In order to idle smoothly, a new engine may require 3 to 5 minutes running above slow idle speed. Idle speed has been adjusted to be correct after this break-in period. TO STOP ENGINE 1. Move throttle control lever to STOP position. 2. Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended. HOW TO USE YOUR SHREDDER Do not attempt to shred or chip any material other than vegetation found in a normal yard (i.e., branches, leaves, twigs, etc.). A WARNING: The shredder discharges material with considerable velocity. Keep away from the area around the chute deflector. Always stop the engine and disconnect the spark plug wire when removing or attaching the bag, when changing containers or when removing the shredded material, wear safety glasses and gloves whenever using your shredder. 1. Leaves and small branches up to 1/2" diameter can be fed into the hopper assembly. See figure 4. If it becomes necessary to push material into the shredder, use a small diameter stick—NOT YOUR HANDS. The stick cannot exceed 1/2" in diameter so it will be ground up if it gets into the impeller assembly. A WARNING: Do not put material larger than 1/2" in diameter into the hopper. Personal injury or damage to the machine could result. Material of a larger diameter may be fed into the chipper chute according to the chart in next column. 2. Bulky material, such as stalks or heavy branches, up to the diameter listed in the chart below should be fed into the chipper chute. See figure 5. A WARNING: Do not attempt to shred or chip material larger than specified in the chart below. Personal injury or damage to the machine could result. Chipper Chute Model Capacity 640A (3.5 HP) 2" 641A (4 HP) 2-1/2“ 645A (5 HP) 3" A WARNING: Make certain the chipper chute door is closed when chipper chute is not in use. IMPORTANT: There is a flail screen located inside the housing in the discharge area. If the flail screen becomes clogged, remove and clean as instructed in the Maintenance section below. For best performance, it is important to keep the shredding blade and the chipper blades sharp. Refer to Maintenance section, page 7. If the composition of the material being discharged changes (becomes stringy, etc.) or if the rate at which the material is discharged slows down considerably, it is likely that the shredding blade and/or chipper blades are dull and need to be sharpened or replaced. 5 FIGURE 5. MAINTENANCE ▲ WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or performing any repairs or maintenance. LUBRICATION Lubricate the p...

Herunterladen

Geben Sie zwei Ziffern: