Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Do not use the Chipper/Shredder while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating the Chipper/Shredder may result in serious personal injury. Dress properly. 5. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Avoid accidental starting. 6. Be sure the Engine Ignition is in the “OFF” position before moving the Chipper/Shredder or before performing any service, maintenance, or cleaning procedures on the unit. Remove adjusting keys or wrenches before turning the Chipper/Shredder on. 7. A wrench or a key that is left attached to a rotating part of the machine may result in personal injury. Do not overreach. 8. Keep proper footing and balance at all times. Use safety equipment. 9. Always wear ANSI approved safety impact goggles, heavy-duty work gloves, and a dust mask or respirator when using this product. ANSI approved hearing protection must also be used. Do not force the tool. 10. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use the Chipper/Shredder if the On/Off Switch does not turn it on 11. or off. Any tool that cannot be controlled with its power switch is dangerous and must be replaced. Store the Chipper/Shredder out of reach of children and other untrained per12. sons. The Chipper/Shredder is dangerous in the hands of untrained users. Keep children away from this product when in use. Store out of reach of children. Maintain the Chipper/Shredder with care. 13. Properly maintained equipment is less likely to malfunction and is easier to control. Do not use the Chipper/Shredder if it is damaged. Tag it “Do not use” until repaired. Check for misalignment or binding of moving parts, breakage of parts, and 14. any other condition that may affect the Chipper/Shredder’s operation. If damaged, have the Chipper/Shredder serviced before using. Many accidents are caused by poorly maintained tools. Service must be performed only by qualified repair personnel. 15. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing the Chipper/Shredder, use only identical replacement parts. 16. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES AND PRECAUTIONS PLEASE NOTE: Your Warranty is voided if you do not put engine oil in the Engine’s crankcase prior to its first use. Before each use, check the oil level. Never run the Engine with low or no engine oil. Running the Engine with low or no oil will permanently damage the unit. The Engine’s Carburetor may need to be adjusted by a qualified mechanic for 1. efficient high-altitude use. Maintain labels and nameplates on the Chipper/Shredder. 2. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Make sure the Chipper/Shredder is located on a flat, level, sturdy surface 3. capable of supporting the weight of the Chipper/Shredder and any additional tools and equipment. Industrial applications must follow OSHA guidelines.4. Never stand on the Chipper/Shredder. 5. Serious injury could result if the machine tips over. Never leave the Chipper/Shredder unattended when it is running. 6. Turn off the Engine before leaving. Be extremely cautious of the rotating Blades in the Chipper/Shredder. 7. Never allow your hands, fingers, or any other part of your body to enter the Chipper or Shredder hopper units. Never place your hands, fingers, feet, or any other part of your body close to 8. the Discharge Opening while the Chipper/Shredder is in operation. Do not look into the Hoppers or Discharge Opening when the machine is run9. ning. Never allow metal, stone, glass, or other foreign objects to be fed into the 10. Chipper/Shredder. Use a stick to push the tree limbs, leaves, etc. into the feed Hopper. Do not attempt to use the machine on a slope or slick surface.11. Always feed branches slowly into the machine.12. Branches larger than 1-1/4” diameter should not be fed into the chipper 13. chute and branches larger than 3/8” diameter should not be fed into the hopper. Do not allow processed material to build up in the discharge area. 14. This may prevent proper discharge and can result in kickback of material through the feed Hopper. If the machine becomes clogged, immediately turn the Engine off. 15. Wait until the Chipper/Shredder comes to a complete stop. Unplug the Spark Plug Wire from the Spark Plug. Then clear the machine of the clogged material. Do not allow children and other untrained people to handle or play with the 16. Chipper/Shredder. Never allow people or animals in the work area. Do not force the Chipper/Shredder....