Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Sears Dateigröße: 2.25 mb Dateiname: Unterrichtssprache:

Check your oil level more frequently to avoid possible engine damage from running low on oil. • Fill engine with oil as follows. Remove oil fill dipstick. See figure 7. With chipper-shredder level, use a funnel to fill engine with oil to FULL mark on dipstick. Capacity is approximately 1-1/4 pints. Be careful not to overfill. Tilt chipper-shredder toward the left (from behind the hopper), then re-level. Check oil level. Refill to FULL mark on dipstick if necessary. Replace dipstick and tighten. GAS Remove fuel cap and fill fuel tank with about 3 quarts of clean, fresh, lead-free grade automotive gasoline. DO NOT use Ethyl or high octane gasoline. Be certain container is clean and free from rust or foreign particles. Never use gasoline that may be stale from long periods of storage In the container. Replace fuel cap. WARNING: DO NOT FILL CLOSER THAN 1/2 INCH OF TOP OF FUEL TANK TO PREVENT SPILLS AND TO ALLOW FOR FUEL EXPANSION. IF GASOLINE IS ACCIDENTLY SPILLED, MOVE CHIPPER-SHREDDER AWAY FROM AREA OF SPILL. AVOID CREATING ANY SOURCE OF IGNITION UNTIL GASOLINE VAPORS HAVE DISAPPEARED. A Check the fuel level periodically to avoid running out of gasoline while operating the chipper-shredder. If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit before it can be restarted. Refer to “Removing the Flail Screen” in Service and Adjustment section. WARNING: EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE. TO AVOID ENGINE PROBLEMS, THE FUEL SYSTEM SHOULD BE EMPTIED OR TREATED WITH FUEL STABILIZER BEFORE STORAGE FOR 30 DAYS OR LONGER. USE FRESH FUEL NEXT SEASON. SEE “STORAGE” SECTION FOR ADDITIONAL INFORMATION. NEVER USE ENGINE OR CARBURETOR CLEANER PRODUCTS IN THE FUEL TANK OR PERMANENT DAMAGE MAY OCCUR. Oil Spark Plug, Fill Wire and Boot Dipstick Muffler FIGURE 8. TO START ENGINE A WARNING: BE SURE NO ONE OTHER THAN THE OPERATOR IS STANDING NEAR THE CHIPPER-SHREDDER WHILE STARTING OR OPERATING. DO NOT OPERATE THIS CHIPPER-SHREDDER UNLESS THE CHUTE DEFLECTOR HAS BEEN PROPERLY INSTALLED AND IS SECURED WITH THE HAND KNOBS. 8 • Attach spark plug wire and rubber boot to spark plug if necessary. See figure 8. • Place the throttle control lever in FAST position. See figure 9. • Move choke lever to CHOKE position. • Grasp starter handle (see figure 9) and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly. NOTE: A noise will be heard when finding the start of the compression cycle. This noise Is caused by the flails and fingers which are part of the shredding mechanism falling into place, and should be expected. In addition, the flails and fingers will be noisy after the engine is started, until the impeller reaches full speed. • Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on start handle. Let rope rewind slowly. Do not let starter handle snap back against starter. • Repeat preceding two instructions until engine fires. When engine starts, move choke lever on engine halfway between CHOKE and RUN. NOTE: If engine does not fire after three attempts, move choke lever halfway between CHOKE and RUN position and try again. See figure 9. CUSTOMER RESPONSIBILITIES V CHECK Choke FIGURE 9. • Move throttle control to IDLE position for a few minutes warm-up. Move choke lever to RUN position as engine warms up. NOTE: In order to idle smoothly, a new engine may require 3 to 5 minutes running above slow idle speed. Idle speed has been adjusted to be correct after this break-in period. TO STOP ENGINE • Move throttle control lever to OFF position. See figure 4. • Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended. 9 GENERAL RECOMMENDATIONS A WARNING: ALWAYS STOP THE ENGINE AND DISCONNECT THE SPARK PLUG WIRE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS. • Periodically check all fasteners and be sure they are tight. • Follow the Maintenance Schedule on previous page. CHIPPER-SHREDDER LUBRICATION Lubricate the pivot points on the chute deflector and chipper chute once a season using a light oil. ENGINE ENGINE OIL Only use high quality detergent oil rated with API service classification SG. Select the oil’s viscosity grade according to your expected operating temperature. Colder - 32°F-► Warmer NOTE: Although multi-viscosity oils (SE30, 10W30, etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your oil level more frequently to avoid possible engine damage from running low on oil. Your four-cycle engine will normally consume some oil—therefore, check engine oil level regularly approximate...

Herunterladen

Geben Sie zwei Ziffern: