Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: MTD Dateigröße: 2.15 mb Dateiname: e9dc80d5-a761-a4a4-9952-57ca88c385cf.pdf Unterrichtssprache:

The heads of the truss machine screws should be to the inside of the upper leaf ramp section. Start all screws and nuts, -then tighten securely. See figure 5. 4 ATTACHING THE CATCHER BAG Your shredder is equipped with a catcher bag to catch the shredded material. To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening. Depress the plunger on the drawstring, pull on the drawstring until the bag is tight around the chute opening. Release plunger to lock it into position. "♦“See figure 6. FIGURE 6. OPERATION KNOW YOUR SHREDDER READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SHREDDER. Compare the illustrations with your shredder to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Hopper Chipper Chute Spark Plug Choke Lever Throttle Control Starter Handle FIGURE 7.—Model 645 Shown OPERATING CONTROLS (See figure 7) RELEASE BAR—Used to release the leaf ramp when raising or lowering. CHOKE LEVER—Used to enrich the fuel mixture in the carburetor when starting a cold engine. STARTER HANDLE—Used to manually start the engine. THROTTLE CONTROL—Controls engine speed and stops the engine. The operation of any shredder can result in foreign objects being thrown into the eyes, which AgQiQggn can result in severe eye damage. F/lAFirv^GuissE^ Always wear safety glasses or eye r sh‘e,c*s- We recommend wide vision safety mask for over spectacles or standard safety glasses. 5 I BEFORE STARTING 1. Place the shredder on a firm, level surface 2. Service engine with gasoline and oil as ins tructed in the separate engine manual packed w th your shredder. 3. Attach spark plug wire to spark plug. NOTE: Check the fuel level periodically to avoid running out of gasoline while operating the chipper-shredder. If the unit runs out of gas as it is sh adding or chipping, it may be necessary to unclog ; he unit before it can be restarted. Refer to “Removing the Flail Screen” on page 8. TO START ENGINE A WARNING: Be sure no one other than the operator is standing near the shredder while starting or operating. 1. Place the throttle control lever in FAST position. See figure 8. 2. Move choke lever to CHOKE position (a warm engine may not require choking). 3. Tecumseh engines only: Prime engine as instructed in separate engine manual. 4. Grasp starter handle (see figure 8) and p jII rope out slowly until engine reaches start of cc impression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly. 5. Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Lot rope rewind slowly. Do not let starter handle sn< ip back against starter. 6. Repeat preceding instructions 4 and 5 until engine fires. When engine starts, move choke lever on engine halfway between CHOKE and RUN. FIGURE 8.—Model 645 Shown 7. Move throttle control to IDLE position fo' a few minutes warm-up. Move choke lever to RL N position as engine warms up. NOTE: In order to idle smoothly, a new engi ne may require 3 to 5 minutes running above slow idle speed. Idle speed has been adjusted to be correct a Her this break-in period. TO STOP ENGINE 1. Move throttle control lever to STOP position. See figure 8. 2. Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended. HOW TO USE YOUR SHREDDER Do not attempt to shred or chip any material other than vegetation found in a normal yard (i.e., branches, leaves, twigs, etc.). A WARNING: The shredder discharges material with considerable velocity. Keep away from the area around the chute deflector. Always stop the engine and disconnect the spark plug wire when removing or attaching the bag, when changing containers or when removing the shredded material, wear safety glasses and gloves whenever using your shredder. 1. Leaves and small branches up to 1/2" diameter can be fed into the hopper when it is in the raised position. See figure 9. If it becomes necessary to push material into the shredder, use a small diameter stick—NOT YOUR HANDS. The stick cannot exceed 1/2" in diameter so it will be ground up if it gets into the impeller assembly. A WARNING: Do not put material larger than 1/2" in diameter into the hopper. Material up to a maximum of 3" in diameter material may be fed into the chipper chute. Do not attempt to shred or chip any material larger than 3" in diameter. Personal injury or damage to the machine could result. 2. Leaves and small twigs can be raked into the shredder when the leaf ramp is lowered to the ground. See figure 10. Small branches up to 1/2" diameter can also be fed into the shredder in this position. See figure 11. FIGURE 10. No Larger Than 1/2" Diameter FIGURE 11. To lower the leaf ramp, use one hand to grasp the handle at the top of the leaf ramp and lift slightly. Pull up on the release bar, and lower the lea...

Herunterladen

Geben Sie zwei Ziffern: