Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung American Power Conversion, modell 230VAC

Hersteller: American Power Conversion
Dateigröße: 361.16 kb
Dateiname: ASTE-6Z8LFR_R0_EN.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Synchronized Turn-on 0 seconds 60, 120, 180, 240, 300, 360, The UPS will wait the speci- Delay 420 seconds fied time after the return of utility power before turn-on (to avoid branch circuit overload). High Transfer Point 230V models: 230V models: To avoid unnecessary bat253VAC 257, 261, 265VAC tery usage, set the high 120V models: 127VAC 120V models: 130, 133, 136VAC transfer point higher if the utility voltage is chronically high and the connected 100V models: 100V models: equipment is known to work 108VAC 110, 112, 114VAC under this condition. Low Transfer Point 230V models: 230V models: Set the low transfer point 208VAC 196, 200, 204VAC lower if the utility voltage is 120V models: 106VAC 120V models: 97, 100, 103VAC chronically low and the connected equipment can tolerate this condition. 100V models: 100V models: 92VAC 86, 88, 90VAC Output Voltage 230V models: 230VAC 230V models: 220, 240VAC 230V models ONLY, allow the user to select the output voltage. 7 4: STORAGE, MAINTENANCE, AND TRANSPORTING Storage Store the UPS covered and positioned as for proper functioning, in a cool, dry location, with the batteries fully charged. At -15 to +30 °C (+5 to +86 °F), charge the UPS battery every six months. At +30 to +45 °C (+86 to +113 °F), charge the UPS battery every three months. Replacing the Battery Module This UPS has an easy to replace, hot-swappable battery module. Replacement is a safe procedure, isolated from electrical hazards. You may leave the UPS and connected equipment on for this procedure. See your dealer or contact APC at the web site, for information on replacement battery modules. Once the battery is disconnected, the connected equipment is not protected from power outages. Be careful during the following steps-the battery module is heavy. REMOVING THE FRONT BEZEL AND BATTERY MODULE Step 1 Step 2 8 1500VA Model Step 3 Step A 1000VA Model Step 3 Battery Terminals Pull the battery module out of the compartment until the back of the module is flush with the outer edges of the UPS. Disconnect the battery connector. Step B Disconnect the battery cable terminals before removing the battery module from the UPS. Note: The red cable connects to the red color- coded terminal; the black cable connects to the black color-coded terminal. This will be important during the battery replacement procedure. Battery Terminals Be sure to deliver the spent battery to a recycling facility or ship it to APC in the replacement battery packing material. 9 REPLACING THE BATTERY MODULE To replace the battery module, reverse the directions above for Removing the Front Bezel and Battery Module. Disconnecting the Battery for Transport Always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department of Transportation (DOT) regulations. The battery may remain in the UPS; it does not have to be removed. 1. Shut down and disconnect any equipment attached to the UPS. 2. Shut down and disconnect the UPS from the power supply. 3. Unplug the battery connector (rear panel). For shipping instructions and to obtain appropriate packing materials contact APC at the web site, 10 5: TROUBLESHOOTING Use the chart below to solve minor Smart-UPS installation and operation problems. Refer to the APC web site, for assistance with complex UPS problems. PROBLEM AND POSSIBLE CAUSE SOLUTION UPS WILL NOT TURN ON Battery not connected properly. button not pushed. UPS not connected to utility power supply. Very low or no utility voltage. Check that the battery connector (rear panel) is fully engaged. Press the button once to power the UPS and the connected equipment. Check that the power cable from the UPS to the utility power supply is securely connected at both ends. Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, have the utility voltage checked. UPS WILL NOT TURN OFF Internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately. UPS BEEPS OCCASIONALLY Normal UPS operation. None. The UPS is protecting the connected equipment. UPS DOES NOT PROVIDE EXPECTED BACKUP TIME The UPS battery is weak due to a recent outage or is near the end of its service life. Charge the battery. Batteries require recharging after extended outages. They wear faster when put into service often or when operated at elevated temperatures. If the battery is near the end of its service life, consider replacing the battery even if the replace battery LED is not yet lit. ALL LEDS ARE LIT AND THE UPS EMITS A CONSTANT BEEPING Internal UPS fault. Do not attempt to use the UPS. Turn the UPS off and have it serviced immediately. FRONT PANEL LEDS FLASH SEQUENTIALLY The UPS has been shut down remotely through software or an optional accessory card. None. The UPS will restart automatically when utility power returns. ALL LEDS ARE OFF AND THE UPS IS PLUGGED INTO A WALL OUTLET The UPS is shut down and the battery is discharged ...