Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Razor Dateigröße: 1.67 mb Dateiname: 380e2266-e47f-412b-a022-ea75f8afdd8d.pdf Unterrichtssprache:

A long-sleeved shirt, long pants, and gloves are recommended. Always wear athletic shoes (lace-up shoes with rubber soles), never drive barefooted or in sandals, and keep shoelaces tied and out of the way of the wheels, motor and drive system. USING THE CHARGER The charger supplied with the E100, E200 or E300 scooter should be regularly examined for damage to the cord, plug, enclosure and other parts, and in the event of such damage, the bike must not be charged until the charger has been repaired or replaced. Use only with the recommended charger. The charger is not a toy. Always disconnect from the charger prior to wiping down and cleaning your scooter with liquid. FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS INCREASES RISK OF SERIOUS INJURY. USE WITH APPROPRIATE CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION. 1 BEFORE YOU BEGIN Estimated Assembly and Set-Up Time Razor recommends assembly by an adult with experience in bicycle mechanics. Allow up to 20 minutes for assembly, not including initial charge time. Allow up to 12 hours for initial charge (see page 3 for charging information. Brake Lever Charger Charger Plug Charger Port Wheel Brake Lever Adjuster Extension Tube Folding System Speed Control Front Fork Tire Battery pack and motor controller Headset T-tube Handlebar height adjust quick-release On/off switch and charging port Locking Knob Required Tools Some tools may be supplied; however, we recommend the use of mechanic’s grade tools. Use the supplied tools only as a last resort. 6mm hexagonal Inflation valve Bicycle-style tire pump key wrench adapter/extender for Schrader valve (included) (with E200 & E300 tires, with pressure only) gauge WARNING: DO NOT USE NONRAZOR PRODUCTS WITH YOUR RAZOR ELECTRIC SCOOTER. The scooter has been built to certain Razor design specifications. The original equipment supplied at the time of sale was selected on the basis of its compatibility with the frame, fork and all other parts. Certain aftermarket products may or may not be compatible. Need Help? Visit our web site for updates and a list of authorized service centers at or call toll-free at 866-467-2967 Monday -Friday 8:00 AM -5:00 PM Pacific Time. 2 ASSEMBLYANDSET-UPq WARNING:Failure to properly tighten the wedge may allow the handlebars to dislodge while riding and may cause you to lose control and fall. When correctly tightened, the handlebars will not rotate out of alignment with the front wheel under normal circumstances. WARNING:Keep your fingers clear of the pivoting mechanism when folding or unfolding the scooter, and make sure others are standing clear. Note: The cable and wire assembly from the handlebar must not wrap around the steering tube or handlebar as shown in step 3. Sharp bends or twisting of the brake cable can cause the brakes to malfunction. q ChargingtheBatteryYour electric scooter may not have a fully charged battery. Therefore it is a good idea to charge the battery prior to use. • Initial charge time: 12 hours • Run time: up to 40 minutes • Recharge time: up to 8 hours, • Average battery life: 250 charge/discharge cycles Battery should be recharged a minimum of 8 hours after each use. When the vehicle is not in regular use, recharge the battery at least once a month until normal use is resumed. 1Plug the charger port into the port on the scooter. The charger works with the power switch in either the on or off position. The charging input, on/off switch and overload breaker are located under the deck at the front left-hand side. 2Plug the charger plug into a wall outlet. WARNING: Always disconnect your scooter from the charger before cleaning with liquid. Note: If your charger does not look like the one illustrated, your unit has been supplied with an alternative charger. The specifications and charging procedure would not change. The charger has a small window with one LED or two LEDs to indicate the charge status. Refer to the illustration on the charger unit for the actual “charging” and “charged” status indications for your model charger. Chargers have built-in overcharge protection to prevent battery from being over-charged. Be sure to properly align the groove on the charger input plug with the corresponding socket on the case; otherwise, no charging action will occur. Charger Plug Charger Port handlebars cannot be twisted out of alignment with the front wheel. 12Remove the plastic protector bar assembly. Insert the “quill” covering the base of the handleheadset. fork until it bottoms on the Slide the quill into the3part of the handlebar assembly into the fork. You may have to loosen the wedge to allow it to slip into the fork. 6Swing the locking knob to the 12 o’clock position and tighten by hand as firmly as possible. WARNING: Failure to recharge the battery at least once a month may result in a battery that will no longer accept a charge. ASSEMBLYANDSET-UPq WARNING:Failure to properly tighten the wedge may allow the handlebars to dislodge while riding ...

Herunterladen

Geben Sie zwei Ziffern: