Stimmen - 5, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Shoprider Dateigröße: 500.96 kb Dateiname: Unterrichtssprache:

Reversing Before reversing ensure that the area behind is free from any hazards or obstructions. Adjust your speed setting to a low setting before you reverse. Press the left thumb lever, and steer wide of all corners and obstacles. Dismounting Before dismounting ensure that the key is turned to the off position. CAUTION: Please ensure that care is exercised when entering or leaving the scooter and that the tiller and foot rest is not used for support. EXTRA GUIDELINES IN THE CONTROL OF YOUR SCOOTER Ramps The stability of your scooter is governed by several factors such as the seating position, the angle of the slope and your height and weight. When approaching an incline, do so directly and not at an angle and where ever possible avoid making turns. When going down a ramp or slope keep the speed settings to slow. This will ensure there is a safe controlled descent. When the finger levers are released the scooter will slowly stop. Caution - Do not turn off the control key while the unit is in motion Grass and Gravel Please follow the guidelines given previously and your scooter will perform admirably over many surfaces. Avoid long grass, loose gravel and sand. NOTE: You should not operate your scooter in wet weather or on wet surfaces. This may cause the motor to short out. 9/22/2004 11 TRANSPORT / STORAGE The scooters are designed to be dismantled into separate sections for transportation and storage. Your scooter can be dismantled into the following sections: XtraLite 3 (Fig. 15) 1) Small Front Basket 2) Large Rear Basket 3) Seat 4) Seat Post & Fasteners 5) Battery Pack 6) Fold Down Frame XtraLite 4 (Fig. 16) 1) Small Front Basket 2) Large Front Basket 3) Seat 4) Seat Post & Fasteners 5) Battery Pack 6) Fold Down Frame Scootie (Fig. 17) 1) Basket 2) Seat 3) Seat Post & Fasteners 4) Rear Chassis 5) Front Chassis 6) Rear Shroud Sunrunner S (Fig. 18) 1) Basket 2) Seat 3) Seat Post & Fasteners 4) Rear Chassis 5) Front Chassis 6) Rear Shroud Figure 15 Figure 16 Figure 18 1 2 6 5 3 4 1 6 5 3 6 2 Figure 17 4 2 4 5 2 1 3 4 1 3 5 6 9/22/2004 12 Dismantling 1. Remove baskets. 2. Fold down the back of the seat. 3. For Sunrunner S: pull up on the red lever under the seat and at the same time lift and twist the seat off. For XtraLite 3; XtraLite 4; Scootie: unscrew the tightening bolt below the seat. Lift seat off. For XtraLite 3 & XtraLite 4 ONLY. 1. Lower tiller toward the foot rest and connect the carrying rod (For XtraLite 3) to the proper location or connect the two Velcro straps (For XtraLite 4) to the handle bars. For Scootie & Sunrunner S ONLY. 2. Remove the rear chassis cover/battery pack. 3. Remove the locking pin and separate the rear drive unit (Fig. 11). 4. Lower the tiller to its lowest level on the front chassis and connect the carrying rod (if the rear drive unit is NOT separated). BATTERIES AND BATTERY CHARGER The Shoprider® scooter is supplied with maintenance free, sealed lead acid batteries. Battery performance can be affected by temperature, terrain, condition of battery, the weight of the user, etc. The battery level indicator is only a guide and is most effective when the scooter is moving, only then is the true discharge level displayed. • When the scooter stops the battery level indicator may indicate full. • An active user can use up to 30% of battery capacity or more per day. • Inactive users may only use 50% of battery capacity in a week. • In both these instances the battery should be put on charge over night. Battery Charger Batteries supplied with your scooter are specially designed. All units require an automatic battery charger. XtraLite 3 and XtraLite 4 have built in charger ports on the side of the battery pack. The battery chargers are 2-amp transformer type off board. Charging To charge the batteries connect the plug lead into the battery-charging socket on the scooter/battery pack and the 2 or 3-prong plug into the wall socket and switch on. FOR Scootie and Sunrunner S ONLY: the battery charger has two lights. The red light when constant shows the battery charger is connected if the red light flashes; there is a break in the connection. A steady green light will show the unit is charging. When the light turns solid red again while still plugged into the charging port the unit is fully charged. DO NOT OVER CHARGE THE UNIT. FOR XTRALITE 3 & 4: Connect 3 prong round plug to their charging port, located on the side of the battery pack. The charger will show a solid green light when plugged in the all. Once plugged into the charging port a steady red light will indicate that the unit is charging. When the red light turns green while still connected to the charging port, the unit is fully charged. DO NOT OVER CHARGE THE UNIT. CAUTION: Always ensure that the charging lead is in good condition and has not been damaged or stretched. 9/22/2004 13 MAINTENANCE Lubrication At six-month intervals you should lubricate the following parts with a light oil or similar lubricant: • Seat pivot post. ...

Herunterladen

Geben Sie zwei Ziffern: