Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Shoprider Dateigröße: 560.56 kb Dateiname: Unterrichtssprache:

Release the lever and the seat will lock in that position. Under the right side of the seat there is a spring loaded red lever. Pulling up on the lever allows the seat to swivel, when released the seat will lock into one of four positions. Seat Slide Lever Swivel Seat Adjustment Lever Figure 6 Seat Removal (Fig. 7) Fold down the back of the seat. Pull up the red swivel seat adjustment lever (fig. 6) and lift seat off. Remove the hand knob and locking pin that secures the seat adaptor. Lift the seat adaptor out of the seat post. Seat Height Adjustment (Fig. 7) Remove seat as described above. Loosen the seat tightening hand knob. The seat height can be adjusted to 5 different settings by inserting the steel locking pin in the required hole. Retighten the hand knob and replace the seat. Armrest Width Adjustments (Fig. 8) On the underside of the seat there are two hand knobs, one either side. Loosening the hand knob allows the arm rest to be adjusted to the required width, or removed for transportation. DO NOT USE SCOOTER WITHOUT THE ARM RESTS BEING FITTED & SECURED. Seat Adaptor Seat Tightening Hand Knob Seat Locking Pin Armrest Adjustment Hand Knob Figure 7 Figure 8 12/29/2004 8 Armrest Angle Adjustment (Fig. 9) Flip up the armrests to allow access to the adjustment screw and lock nut, unscrew the lock nut and screw the bolt in or out to increase or decrease the angle. Re-tighten the lock-nut. The armrests are set parallel to the floor at the factory. Reclining Seat (Fig. 10) Sprinter XL4 Deluxe & Sprinter XL3 Deluxe The Sprinter XL4 Deluxe and Sprinter XL3 Deluxe come standard with a reclining seat. The reclining seat lever is located on the left side below the armrest. Simply pull the lever up to adjust. This feature also allows the seat to be folded down. Locking Nut and Bolt Adjustment Screw Figure 9 Figure 10 12/29/2004 9 SCOOTER TILLER CONTROLS (FIG. 11A, 11B & 11C) Speed Controls The speed control dial allows you to set a speed between 1 (minimum) and 10 (maximum). The Sprinter XL3 Deluxe, XL4 Deluxe, and Jumbo XL are also equipped with a speed high/low switch. Battery Level Indicator/Gauge The number of LED bars lit/where the needle rests, shows the amount of charge left in your batteries. The amount of charge will only show at its true level when the scooter is in drive. CAUTION – Do not allow the LED bars/gauge needle go out/down completely as complete discharge of the batteries could cause irreversible damage. Lights A blue button located at tiller controls operates lights. Horn A yellow button located at the tiller controls operates the horn. Thumb/Finger Accelerator Lever Controls The right thumb/finger accelerator lever controls the forward motion and the left thumb/finger accelerator lever controls the reverse motion. The amount of pressure applied to each lever will determine the speed the scooter travels at. Release the lever and the scooter will slowly come to a stop. On/Off Key Switch Insert the key in the right side of the tiller. Turn the key and the LED bars will light up/needle gauge will move to the right. There is a delay before the thumb/finger lever accelerator control can be operated, while the controller checks the circuits. Indicator Switch Sprinter XL4/XL3 Deluxe, Sprinter Jumbo XL Operates turn indicator lights. Hazard Warning Switch Sprinter XL4/XL3 Deluxe & Jumbo XL A red button operates all hazard flashers. Electromagnetic Brake Figure 11A Sprinter XL4 Light Figure 11B Sprinter XL3 Deluxe & Sprinter XL4 Deluxe Speed Controls Horn Key Switch Thumb Lever Control Speed Control Speed High/Low Switch Horn Key Switch Lights Hazard Lights Finger Lever Control Indicator Switch Battery Level Indicator Battery Level Indicator Charging Port Figure 11C Sprinter Jumbo XL Key Switch High/Low Switch Battery Level Indicator Indicator Switch Lights Finger Lever Control Horn Speed Controls Charging Port The brake is automatically operated when the thumb/finger accelerator control levers are released. There is a slight delay when the scooter decelerates; this allows the scooter to come to a smooth stop. 12/29/2004 10 Figure 12B Sprinter XL4 Rear Chassis Cover Scooter Serial Number Anti-tip Wheels Freewheel Release Lever Circuit Breaker Figure 12B Sprinter XL4 Rear Chassis Cover Scooter Serial Number Anti-tip Wheels Freewheel Release Lever Circuit Breaker FREE WHEEL OPERATION (FIG. 12A & 12B) The free wheel lever allows you to put the scooter in neutral and push it. The free wheel release lever is located toward the inside of the rear wheel (Fig. 12A & 12B). To push the scooter (neutral), push the free wheel lever down. To put the scooter in gear (drive), lift the lever up. The scooter will not operate when the lever is down (neutral). WARNING! For safety, always put the scooter into gear (lever up) after pushing or rolling scooter. Failure to do so may result in injury. Anti-tip Wheels The anti-tip wheels are located at the rear of the scooter frame (Sprinter XL4) (Fig. 12B). The scooter shoul...

Herunterladen

Geben Sie zwei Ziffern: