Stimmen - 5, Durchschnittliche Bewertung: 3.4
(
)
)
|
Anleitung Zusammenfassung
• To assemble your lift, begin by inserting the Post into the Arm assembly. Next, slide the Power Frame onto the top of the Post. Line up the Red stripe on the Power Frame, Rotation Limit Collars, and Arm assembly. • Plug in the Hand Control. • By pressing the DOWN button on the Hand Control harness, run the Strap Hook down until it is slightly lower than the docking device on the scooter. • Attach the Strap Hook to the docking device on the scooter or chair and remove any play in the strap by pressing the UP button on the Hand Control until tension is felt. Caution: Ensure that the Lifting Strap is secure and taught and that it points straight down. Failure to do so could result in the scooter or chair swinging toward the vehicle or operator. • Raise the scooter using the UP button until the scooter or chair is just above the trunk lip. Caution: Stop lifting before the Strap Hook contacts the Strap Roller mounted on the Power Frame. Contact will result in damage to the lift. A properly adjusted and operated lift will avoid this. • Swing the scooter or chair out of the vehicle, carefully ensuring that the scooter does not contact the vehicle. • With the scooter or chair positioned away from the vehicle, lower the lift using the DOWN button. Continue lowering the lift slightly beyond the scooter or chair touching the ground to allow removal of the Strap Hook from the docking device on the scooter. • To disassemble the lift, first raise the Lifting Strap until the freed Strap Hook is about an inch away from the Power Frame. Unplug the Hand Control harness from both the Vehicle Harness and the Power Frame. • Pull the Power Frame off of the Post and lay it on the floor of the trunk. Then pull the Post out of the Arm assembly and set it down with the Power Frame. 8 SAFETY: • Caution: Do not operate this lift until your dealer has satisfactorily instructed you in the proper operation of the lift. • Your Harmar Lift has been engineered and designed for years of trouble free use. Although, with everyday use, some parts may become loose or worn. IMPORTANT! Check regularly for any worn, loose or damaged parts of your lift. If anything is observed, DO NOT USE THE LIFT! Contact your dealer or installer of the lift for repairs to be made. Failure to act may cause severe injury! • Your Harmar Lift should only be used for the loading and unloading of scooters and power wheelchairs for which it is designed. DO NOT add to or modify any part of the lift system without first contacting the manufacturer of the lift. Any modifications may void any warranties as well as effect the structural integrity of the lift. • ALWAYS CHECK THE LIFTING STRAP BEFORE EACH USE FOR DAMAGE OR WEAR. • Always make sure the vehicle’s parking brake is firmly set before operating the lift. • Caution: Insure that the Lifting Strap is secure and taught and that it points straight down before lifting of the scooter or power chair. Failure to do so could result in the scooter or chair swinging toward the operator of the vehicle. • Caution: When using the lift, keep your hands and feet from under the scooter or power chair as it is being loaded or unloaded. • Caution: Stop lifting before the Strap Hook contacts the Strap Roller mounted on the Lifting Arm. Contact will result in damage to the lift. A properly adjusted and operated lift will avoid this. • Caution: Insure that the scooter or chair is firmly sitting on the floor of the vehicle and not suspended by the lift. If the scooter or power chair is not firmly on the floor of the vehicle, it may move during transportation and cause damage to the lift, scooter or power chair, vehicle, or passengers. MAINTENANCE: The Harmar Lift has been designed to be as trouble free as possible for the owner. But, as with any mechanical device, regular care should be given while owning and using this device. Maintenance is no exception. • We recommend that dealers should schedule a preventative maintenance inspection at least once a year on motors, lift frame, wiring harness and all moving parts of the lift. • Check for paint chips and touch up any bare metal with a good gloss black enamel or lacquer to inhibit rust. This may be necessary more frequently when subjected to salt air or road salt. • Always check the lifting strap before each use. If any wear or fraying is noticed DO NOT USE THE LIFT! Contact the installer or dealer for repair. Failure to act may cause damage to the vehicle or severe injury! • Hand control units should not be exposed to the weather. If the lift is mounted in the bed of a truck, remove the hand control between each use. Exposure to the elements may cause the unit to fail. WARRANTY: This lift is covered by a one year factory warranty on materials and workmanship. Contact your local dealer for more information or go to for complete details. 9 TROUBLESHOOTING: PROBLEM: The lift will not operate or operates slowly. Possible Causes: Bad Connection—Verify the vehicle wiring harness...