Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
This manual is written to be used both as an installation guide as well as an operation guide for the end user for both the AL010 Micro Scooter Lift and AL030 Manual Wheelchair Lift. Refer to the index below for the sections that apply to your lift and options. Please read the manual thoroughly BEFORE attempting any installation, adjustment or use of the lift. Both installers and operators should familiarize themselves with this entire manual. The manual will be divided into the following sections for easy reference; Section 1 - Unpacking the Lift Section 3 - Vehicle Preparation Section 4 - Installing the Lift ( No Swing Away ) Section 5 - Installing the Lift ( with Swing Away Option ) Section 6 - Operating the AL105 Swing Away Option Section 7 - Operating the AL010 Micro Scooter Lift Section 8 - Operating the AL030 Power Tote Lift Section 9 - Adjusting the AL010 and AL030 Section 10 - Safety & Maintenance Section 11 - Troubleshooting Guide If you have any questions or comments concerning the installation or operation of your scooter/chair lift, please contact your local distributor for additional technical information. Only authorized dealers should install this lift. Section 2 - Wiring the Vehicle Caution: Some scooters and chairs may be unsuitable for transport in or on a motor vehicle. Please contact the manufacturer of your mobility device to determine its transportability. Section 1 - Unpacking the Lift Your Universal Outside Lift was factory pre-assembled to require little assembly before installation. Box contents should include: AL010 - Micro Scooter Lift LIFT BODY HARDWARE PACK AL030 - Manual Wheelchair Lift LIFT BODY HITCH ADAPTER and Stabilizer HARDWARE PACK Each AL010 is packaged standard with a standard Class 2 hitch adapter. Each AL030 is packaged with a standard Class 1 flat bar style hitch adapter and stabilizer. If a Class 2 or Class 3 hitch adapter or Swing Away option is required, separate parts must be ordered. See Section 5 for installing a lift with the Swing Away option in this manual. Be sure and check the contents of the box against the package check list to be sure that all parts are included with the lift that are required for proper installation. If any parts are missing or if any damage is noted, immediately contact the distributor from which you purchased your lift. DO NOT attempt to install or use the lift with any missing or damaged parts. "PLATFORM KEEPER" NOTE: The Platform will not be allowed to unfold until the platform has been lowered at least 1 inch. WELDED TO PLATFORM LIFT CLASS 2 Hitch Adapter OR OR CLASS 3 CLASS 3 OR CLASS 2 OPTIONAL OPTIONAL OPTIONAL HITCH POST HITCH POST Section 2 - Wiring the Vehicle Important Note: IMPROPER WIRING IS THE #1 CAUSE OF PROBLEMS IN THE OPERATION OF A VEHICLE LIFT. FOLLOW THE WIRING INSTRUCTIONS CAREFULLY Located in the hardware package is the vehicle wiring harness. The harness is manufactured to, and complies with the SAE J1128 requirements. The wire harness is approximately 23 ft. long and will accommodate most vehicles. To back Unwind the harness and lay it flat. One end of the To vehicle'sbattery of vehicle harness has a black plug . This is the lift end of the harness and goes to the back of the vehicle. BLACKWIRE BLACKWIRE OR Begin routing the wiring harness at the vehicle battery. Attach the black wire to the negative terminal on the battery. Do not attach the red wire yet. Side mount Top mount Run the wiring harness under or when possible through the vehicle, back to the trailer hitch. Always locate the wiring harness where it can not be snagged by road debris and away from the vehicles gas tank. If the harness is too long for the vehicle, coil the excess wire and secure it to the vehicle frame with the supplied tie wraps. Do not cut or shorten the harness. Secure the plug about even with the end of the hitch receiver tube. Attach the red wire to the positive terminal on the battery. RED WIRE RED WIRE OR Side mount Top mount Important Reminder: Never attempt to attach the wire harness to a secondary power source, The lift requires direct connection to the battery. Caution: When the installation requires the wiring harness be run on the underside of a vehicle, route the harness away from the exhaust system, brake lines, fuel lines, gas tank, pinch points, and sharp edges. Locate the wiring harness where it can not be snagged by road debris. Manufactures Recommendation: Schedule a routine maintenance visit with the end user. Harmar recommends the lift be greased in the applicable areas, and the wire harness connections be checked for corrosion, and/or decay, as such conditions are normal due to environmental changes. Section 3 - Vehicle Preparation To install the lift on a vehicle, it must be capable of accepting a hitch. If you are unsure about the hitch required, there are different places for you to check. Hitch Shops - Check your local area for shops that specialize in trailer hitches. They will normally have in stock the...
Dieses Handbuch ist für folgende Modelle:Rollstühle - AL030 (1.24 mb)