Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Empire Comfort Systems, modell VFSUR18-2

Hersteller: Empire Comfort Systems
Dateigröße: 2.22 mb
Dateiname: c6df67d0-6bb5-484a-8208-0df2bccd9fe4.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

3. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa). Attention! If one of the procedures results in pressures in excess of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will result in a hazardous condition. Page 14 25741-0-0309 25741-0-0309 Page 15 Over time, the rockwool will break down and new rockwool will need to be placed to recreate the original glowing embers effect. Remove all old rockwool from the appliance and apply new rock as described in this section or the log manual. Note: Only the rockwool supplied with this unit or ordered in accordance with the Parts List on page 20 should be used on this burner. See the Parts List on page 20 to order replacement rockwool. Placing Lava Rock in Front of Burner on Fireplace Floor Spread lava rocks on fireplace floor in front and sides of the burner pan. The lava rocks are for decorative effect and are not required for fireplace operation. Attention: Do not place lava rocks on Burner, logs or rockwool. The lava rocks should only be placed on the fireplace floor. Flames from the pilot (rear right back side of the pan burner) as well as the main flame should be visually checked as the log set is installed. In normal operation at full rate after 10 to 15 minutes, the flame appearance should be sets of yellow flames. NOTE: All flames will be random by design, flame height will go up and down. Glowing embers (rockwool) can cover the pan burner in between the front and middle logs, but very little is necessary to cover this area. Excess ember material causes the yellow flame to become orange and stringy. Apply just enough to obtain slow glow and a gold yellow flame. Avoid any drafts that alter burner flame patterns. Do not allow fans to blow directly into fireplace. Do not place a blower inside the burner area of the firebox. Ceiling fans may create drafts that alter flame patterns. Sooting and improper burning will result. During manufacturing, fabricating and shipping, various components of this appliance are treated with certain oils, films or bonding agents. These chemicals are not harmful, but may produce annoying smoke and smells as they are burned off during the initial operation of the appliance, possibly causing headaches or eye or lung irritation. This is a normal and temporary occurrence. The initial break-in operation should last 2-3 hours with the burner at the highest setting. Provide maximum ventilation by opening windows or doors to allow odors to dissipate. Any odors remaining after this initial break-in will be slight and will disappear with continued use. Figure 12 Placement of the glowing embers (rockwool) is very individual and light coverage will provide your best effects. We recommend separation of the rockwool by hand and make your coverage as light and fluffy as possible. Place just enough rockwool on the burner to obtain the glow and a gold, yellow flame. Do not place rockwool over large ports in rear portion of burner. Rockwool should not be placed in the area of the pilot assembly. Application of excess rockwool may adversely affect performance of the heater. WARNING: All previously applied rockwool must be removed prior to reapplication. PLACE MENT OF GLOWING EMBERS AND LAVA ROC K OPERATION INSTRUC TIONS/FLAME APPEARANCE Note For Burner Port Ignition: Due to the size of the burner, there may be a small delay before all burner ports ignite. Page 16 25741-0-0309 Wa rning: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFO RE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • D o not try to light any appliance. • D o not touch any electrical switch; Do not use any phone in your building. • Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. C. U se only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. D o not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. 1. Open bottom louver assembly (if applicable). 2. Set REMOTE/OFF/ON switch to OFF. 3. Turn off all electric power to the appliance if service is to be performed (if applicable). 4...