Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Empire Comfort Systems, modell 30

Hersteller: Empire Comfort Systems
Dateigröße: 1.02 mb
Dateiname: 5014ed3a-90b6-75f4-2990-82ed98c97fcb.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

WARNING: Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns. WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater. Candles Avoid the use of scented or decorative candles while the fireplace is in operation. Candles produce a residue in the air that creates a soot like substance. Burning candles while the fireplace is operating magnifies the problem. It should be noted that candles, in general, produce soot. The amount of time burned and the quantity of candles burned will determine the amount of soot produced and deposited. Make Owners Aware of Proper Log Set Operation Properly installed and properly maintained log sets do not deposit soot on the logs. If users see soot appear on a log, call for service. Do not continue to operate the log set. 20253-1-0806 Page 3 Page 4 20253-1-0806 Before you begin: Do not, handle these logs with your bare hands! Always wear gloves to prevent skin irritation. After handling logs, wash your hands gently with soap and water. All Logs The positioning of the logs is critical to the safe and clean operation of this heater. Sooting and other problems may result if the logs are not properly and firmly positioned in the appliance. Refer to Figure 1 for the following warning. Warning: Failure to position the parts in accordance with this diagram or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. PROPER INSTALLATION SEQUENCE: VFP(32.36)FP (Figure 1) 1. Place rear (#1) log onto two (2) pins on rear log support. 2. Place left, front (#2) log onto two (2) left, front pins on burner pan. 3. Place right, front (#3) log onto two (2) right, front pins on burner pan. 4. Place Y Branch (#4) onto 2 pins on rear log. 5. Compare the completed log installation with the appropriate photo from pages 4 and 5. Review previous steps to make any necessary adjustments. 6. Log placement is completed. Attention: Do not use Figure 1 to order replacement logs. Refer to Page 6 Parts List and Parts View to order logs for your appropriate model number. Apply loose material (glowing embers) per appropriate Installation Instructions and Owner's Manual. Replacement of loose material (glowing embers) must be purchased from Empire Comfort Systems, Inc. Application of excess loose material (glowing embers) may adversely affect performance of the heater. WARNING: All previously applied loose material must be removed prior to reapplication. GENERAL INFORMATION Qualified Installing Agency Installation and replacement of gas piping, gas utilization equipment or accessories and repair and servicing of equipment shall be performed only by a qualified agency. The term "qualified agency" means any individual, firm, corporation, or company that either in person or through a representative is engaged in and is responsible for (a) the installation, testing, or replacement of gas piping or (b) the connection, installation, testing, repair, or servicing of equipment; that is experienced in such work; that is familiar with all precautions required, and that has complied with all the requirements of the authority having jurisdiction. LOG PLACEMENT Replacement Loose Material (glowing embers) Part Number Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement VFP(32,36)FP Figure 1 The following WARNING applies when log set is installed onto an unvented gas burner assembly. WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is not permitted. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA54.* *Available from the American National Standards Institute, Inc. 11 West 42nd St., New York, N.Y. 10018. State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts. Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a copy of 527 CMR-30 upon sale of the unit. 1 2 3 4 VFP(32,36)FP 15970 Platinum Bright Embers PE-20-1 VFP32FP(20,21,30,31)L(N,P) 20253-1-0806 Page 5 Donotcoveranylargerearportswithloosematerial(glowingembers) Photo 2 Photo 1 Photo3 Photo4 VFP36FP(20,21,30,31)L(N,P) PHOTOS Do not cover any large rear ports withloose material (glowing embers) Photo 2 Photo 1 Photo 3 Photo 4 Page 6 20253-1-0806 PARTS LIST & PARTS VIEW Attention: When ordering parts, it is very important that part number and description of part coincide. Index Part Number Description No. VFP32FP(20,21,30,31)L(N,P) 1 R-8306 BACK LOG 2 R-8304 LEFT FRONT LOG 3 R-8305 RIGHT FRONT LOG 4 R-8307 Y BRANCH VFP36FP(20,21,30,31)LN,P) 1 R-8310 REAR LOG 2 R-8308 LEFT FRONT LOG 3 R-8309 RIGHT FRONT LOG 4 R-8311 Y BRANCH 1234 USE ONLY MANUFACTURER'S REPLACEMENT PAR...