3 OPERATION.................................................................6 MAINTENANCE............................................................7 STORAGE..................................................................... 7 SERVICE AND ADJUSTMENTS..................................8 TROUBLESHOOTING.................................................. 8 REPAIR PARTS EXPLOSION....................................10 REPAIR PARTS LIST.................................................11 SAFET

Slip elastic opening of bag over air duct assembly. See figure 7. X BAG (M) FIGURE 7. HAIR PIN COTTER (B) \ CLUTCH GRIP ASSEMBLY (A) CLEVIS PIN (C) NOTE Steps 6, 7 and 8 for self-propelled units only. 6. Assemble the clutch grip (A) to the left hand side of upper handle. Secure in place with clevis, pin (C) and hair pin cotter (B). See figure 8. Head of clevis pin should be to the outside of handle. FIGURE 8. LOCK NUT (E) EXTENSION SPRING (D) 7. Slide the extension spring (D) onto

No. Part No. Color Code DESCRIPTION Slew Part Ref. No. Part No. Color Code DESCRIPTION New Part 1 05778 Clutch Grip Ass'y.t 39 08187 Gear Box Cover t 711-0679 Clevis Pin .375" Dia. x 1.88" 40 748-0135 Bevel Gear .62" I.D. x 28 Lg.t Teeth t 3 747-0154 Clutch Rod 32 1 Lg. t 41 715-0246 Spring Pin Spiral 3/16" Dia. 4 749-0482 Handle Brace <5 H.P.Tecumseh) N x 1.25" Lg. t 749-0483 Handle Brace (5 H.P. Briggs & 42 710-0726 Hex Wash. Hd. "AB" Tap Scr. Stratton)

Slide housing and impeller off engine crankshaft. Be careful to not lose square key. See figure 19. ENGINE CRANK S P.T.O. PULLEY FIGURE 19 10 5. Slide belt off crank shaft. 7. Remove belt from P.T.O. pulley and install new belt. See figure 19. NOTE When reassembling the new belt, the aid of another person will be helpful. 8. Turn the crankshaft until the key way on shaft is directly on top. While holding housing assemlby and impeller assemlby, line up the key way on the pulley with the

Do not allow rope and handle to snap back into place. 3. After two or three full firm pulls on recoil (or as soon as engine fires), move speed control to run position. 4. Self Propelled Models Only - To engage the drive mechanism, squeeze the clutch grip against the upper handle. Release the clutch grip to stop the forward motion. FIGURE 16 CARBURETOR ADJUSTMENT TO STOP ENGINE 1. To stop engine, move throttle control lever to STOP position. 2. Disconnect spark plug wire and ground to prev

x 1.00" O.D. 33 14571 -- 488 Caster Arm Ass'y. x .305" Lg.t 34 08348 Drive Shaft .624" Dia. x 74 736-0175 L-Wash. .265" I.D.t 22.75" Lg.t 75 710-0352 Hex Self Tap Scr. 1/4" x ^5 748-0136 Bevel Gear .50" I.D. x 14 3/8" Lg.t Teeth t 76 14556 R.H. Pinion Guard t 36 748-0108 Flange Bearing .503" I.D. t 14555 L.H. Pinion Guard (Not Shown) 37 08189 Gear Box t 77 712-0298 Hex Jam Nut 1 /4-20 Thd. t 38 748-0110 Flange Bearing .630" I.D. t 78 736-0242 Belle

Do not change grease; simply acid if necessary. MAINTENANCE A (*warnTng*J Disconnect spark plug wire and ground it against the engine before performing any repairs or maintenance. BELT REPLACEMENT (Self-Propelled Models Only) 1. Remove the nozzle or impeller guard from front of blower housing. 2. Remove hex bolt and lock washer from cen :er of impeller. See figure 18. A 9/16" socket wench with extension is needed. 3. Remove hand knob and belleville washer from top of housing. 4. Remove t

C. Fill crankcase with the proper oil. NOTE: For repairs beyond the minor adjustments listed above, please contact your local service dealer. 11 I Models 675, 685 and 689 ) ' с JW-вл-Г 12 Models 675,685 and 689 ^ PARTS LIST FOR MODELS 675, 685, 689, 240677 and 240687 POWER VACUUMS REF. NO. PART NO. COLOR CODE DESCRIPTION New Part REF. NO. PART NO. COLOR CODE DESCRIPTION New Part 1 05778 Clutch Grip Ass'y.t 41 715-0246 Spring Pin Spiral 3/16” Dia. 2 711-0679 Clevis Pin .375” Dia.

x 1.75" 26 14570 Gear Box Mounting Brackett 69 714-0145 Internal Cotter Pin 3/8" Dia. 27 732-0376 Extension Spring .75” O.D. x 70 749-0786 Upper Handle (Painted) 3.28” Lg.t 749-0480 Upper Handle (Chrome) 28 14565 Clutch Bracket Ass'y.t 71 738-0185 Rear Axle .624" Dia. x 24.37” 29 714-0229 #2 Woodruff Key 3/32” Dia. 72 715-0249 Spring Roll Pin 5/32" Dia. x .81" Lg.t x 1.12t 30 748-0227 Hex Flange Bearing Bronze 73 750-0142 Spacer .82" I.D. x 1.0" O.D.

Secure with one hand knob (F) and belleville washer (G). See figure 4. NOZZLE (N) FIGURE 4 UPPER HANDLE (O) 2. Place the upper handle (0) in position over lower handle. Fasten with four hex bolts (I) and lock nuts (J) provided. See figure 5. Two 7/16" wrenches are required. FIGURE 5 3. Place the stud pins (K) in holes in upper handle (head of pins go to the inside of handle). Secure pins with push-on speed nuts (L) by holding speed nut with box wrench and tapping pin with hammer. See figur